Your cart is empty.
Your cart is empty.Product Description
Product Information
- The product exists warpage deformation, but the product will not have any impact on the use. It is not recommended to be used for work environments with high requirements for coaxiality.
- If the length of product is 25mm, there is 0.25mm of warpage deformation; when the length of the product is 200mm, the product exists 2mm warpage deformation. Note: Product specifications below 10mm in diameter (inclusive) are applicable. Warpage check method: three-jaw chuck clamping, check the runout of the other end, the specific check value as described above.
- High Speed Steel (HSS) is also known as air hardening steel or steel. It is an alloy steel of complex components, including tungsten, molybdenum, chrome, vanadium, cobalt carbide forming elements. Amount of alloying element is approximately up to 10-25%. Under high temperature of about 500℃, High Speed Steel still can keep high hardness of 50HRC above. Red Hardness is the main features of High Speed Steel.
High-speed Steel Tool
High-speed steel rods are with combination of hardness and toughness for wear resistance, high temperature resistance, high-speed performance.
Thomas Clark
Reviewed in the United States on June 9, 2024
They are nice sturdy posts, and was what I was looking for for my application
J. Wolf
Reviewed in the United States on June 16, 2024
I needed 6mm HSS rods that were heat treated and that is just what I received. The only minor issue is the manufacturer laser engraves on the side. This could be a problem in some applications but not in most. I'm ordering more.
MICHAEL
Reviewed in Canada on February 10, 2024
Quality 4mm HSS rods and reasonably priced. Would buy again.
Brian Adams
Reviewed in the United States on November 15, 2024
I bought 1.7mm x 200mm for clearing the filament receptacle on my Prusa MK3 3D Printer, and it works like a charm. After disabling the automatic feeder I am able to insert to steel rod and clear out any filament blockages. My only complaint is the Prop 65 Warning indicating that the steel rod is going to give me cancer or cause birth defects.
Mécanoinfernal
Reviewed in Canada on April 8, 2023
C'est se que je cherchais merci
Mccracken
Reviewed in the United States on April 7, 2023
I assumed that being listed as 5mm ment it would be 5mm. Guess thats my fault for assuming such idiotic ideology.. because it is not 5mm
R. Scott
Reviewed in the United States on May 27, 2022
I made wood turning tools from these. Inexpensive HSS bar made very low cost lathe tools.
David Zakar
Reviewed in the United States on March 25, 2022
Bought these to replace a bent rod from my DAA powder check. Did the job, and is straight and squared enough for that purpose. 150mm is a little shorter than the factory rod (which seemed to be closer to 175mm), but still has enough height to do the job. 200 would presumably work fine as well.
Badrad
Reviewed in the United States on April 11, 2022
As others have said, they are fairly straight, but definitely not precision. They may work for a hobby machinist like myself, but I can’t fully recommend.
Michael MacLeod
Reviewed in Canada on May 29, 2020
Product is exactly as advertised. Seems to be good quality, will know better after I reshape and sharpen for wood turning tools. Retailer was as prompt as possible in getting these to me.Would order from them again.
RizzleHizzle
Reviewed in the United States on May 18, 2020
0.03mm is 0.0012" inches, so applying rounding errors, safe to say pieces were kept to a tolerance of about +/- 0.001" which is very good. (My digital calipers had a precision of 0.01mm and 0.001" respectively so 0.3mm could have been 0.025mm - 0.035mm and 0.001" is really 0.0005" to 0.0015" inches.Two of the pieces were slightly less than 4.00mm and three were slightly over 4.00mm, which makes me think it's a 50/50 shot of getting over under. The parts I needed these for were 4.00mm bore (some were other uxcell parts) and they had their own tolerances. For the least frustration (not the fault of uxcell here) I recommend buying twice the amount you think you need if you need slightly under sized to fit through 4.00mm bore metal parts.Even the slightly over sized (4.03mm) rods could be press fit (hammered) through the tighter 4.00mm bores of the parts I was using, but I personally preferred under sized rods to slide through.
Recommended Products
$31.01
$ 15 .99 $15.99