Your cart is empty.
Your cart is empty.4.2 out of 5 stars
- #9,348 in Industrial & Scientific (See Top 100 in Industrial & Scientific)
- #2 in Industrial Dispensing Nozzles
Product Description
Thicker & Wider
We make thicker and wider gaskets to ensure a good, tight fit to the can spouts.
Anti-Overflow
The spout tube and the spout cap are threaded, and the spout cap has a rubber sealing ring inside. Tighten the spout cap after use. There will be no oil overflow even in the case of transportation or the tank is down.
Flexible & Durable
Gas can spouts are excellent and flexible! You can fuel without using a funnel, and there was no leaking or dripping, even with flexing and pressure on the spout.
Allison Abramowitz
Reviewed in the United States on March 1, 2025
Awesome way to improve your gas jugs. Get this set and throw away the junk that came with your gas jugs.
jordan simon
Reviewed in the United States on February 24, 2025
Installed nicely. Spout vent caps-a work well. Caps-b did not thread properly on can. Overall pleased at this time, hopefully they endureth. But they claim to "Strengthen & Thicken" also that they are "Durable" so hope is high.
Mark D.
Reviewed in the United States on January 20, 2025
So the weather has been nasty the last couple of weeks and I didn't try these immediately. My nozzles was the only thing bad on my cans and I was thinking this kit had multiple cap sizes...I didn't double check my cap measurement. These caps are way too small for my cans, I still haven't measured but I'd say my caps are in the 2+ inch range,in order to make these work I'm going to have to 3d print an adapter so the nozzle itself doesn't slide back down into my can. It is an impressive set it even came with a drill bit and air hole plugs for the cans that have the stupid push style nozzle with the built-in air tube, I hate those things, if you have that style can this probably would work fine, just double check the measurements on your cap.
Weldkitt
Reviewed in the United States on January 15, 2025
The quality of the nozzles and caps (two different threaded caps to fit fine or course threaded container fill spouts) are a great replacement for older five-gallon fuel containers. The added bonus with this kit incorporates vent caps AND a correct-sized drill. NOTE: Some older fuel containers do not have an air vent. Current fuel containers were drilled at least 1 1/2 to 2 inches above the fuel full line on each EMPTY container (enables removal of drill shavings). The new vent cap easily pressed into the drilled hole with the help of a scrap piece of plywood, gasket material, whatever works by placing over the vent assembly then pressing the vent through the drilled hole (saves wear and tear on bare thumbs)
Patrick
Reviewed in the United States on January 11, 2025
Easy to install and works wellOnly one bad thing was one of the air caps broke very quicklyWould recommend
Ben B.
Reviewed in the United States on December 8, 2024
I can’t speak to how the plastic nozzles will hold up over time, as I’ve just installed these nozzles on 3 of my fuel cans. Just bought a second kit as I have many more to convert over from the horrible safety nozzles with no vent. Glug glug glug!! This kit comes with everything you need to do it, even a drill bit for installing the vents! And two different style caps that fit most fuel cans so very universal. So far no leaks but like I said we will have to see how they hold up over time. But for the price and convenience you can’t beat it!!
Bill F.
Reviewed in the United States on October 31, 2024
Dump those leaky difficult to use gas can spouts! Works fine on Blitz gas cans. Other make cans you might have to save the original screw on ring. Did not fit an old school metal can. Much easier to use than those spring loaded spouts and can be just as leakproof if you don’t lose the spout caps. They arent tethered like the snap in vent caps but should be.
Justin M
Reviewed in the United States on December 28, 2023
I don't know why it took me so long to think of looking to see if you can order old style spouts but I'm dang happy I did. I'll have to see if I actually end up putting the venting holes in but might not since I have to think about it only when the cans are empty. I have several cans and they almost are all getting these spouts. The kind with the push with your thumb pull with fingers for 2cycle isn't bad but all those new ones suck for putting into a vehicle. Without the vent and that dumb push on spout one it literally took me like 15+ minutes and spilling gas friggin everywhere to empty a partial 5 gallon can in my van, not cool. I was filling up a lawnmower one time with the new style ones and was just drenching my lawn mower in gas. I ripped the stupid thing off, threw it randomly in the yard, poured it without a spout without spilling and then went and ran the dumb thing over with the lawnmower. Some of the worst most aggravating things ever.
Recommended Products