Your cart is empty.
Your cart is empty. Windshield Washer Reservoir
Fitment
Compatible with: 1987-97 Ford F150 Truck without Low Fluid Sensor
Compatible with: 1989-92 Ford Ranger without Low Fluid Sensor
Compatible with: 1987-96 Ford Bronco without Low Fluid Sensor
Compatible with: 1989-90 Ford Bronco II without Low Fluid Sensor
Product Attributes
Mounting Hardware Included: No
Fluid Level Sensor: No
Material: Plastic
Washer Pump Included: Yes
Includes: Cap
Includes: Coolant Reservoir
Reference Numbers
Ford: E7TZ 17618 B, E7TZ17618B
Partslink Numbering System: FO1288171
E. A. Boland
Reviewed in the United States on January 15, 2025
We purchased two of these washer fluid tanks because our two Hyundai Santa Fe both had cracks in the original tanks which caused leaks. These items look to be identical to the OEM tanks and the electrical connections are exactly the same. The fluid pumps work fine in the new tanks but both of our cars now have a "low fluid level" warning on the dashboard. I took the original level sensor out of one of our original tanks and the warning light on the dash goes away. Be aware of this before going through the trouble to replace this windshield washer fluid tanks.
Joseph Cozzarelli
Reviewed in the United States on January 1, 2025
Fit my Jeep perfextly. They also have a link on youtube that demonsraites installation. Very helpful
cgsinger
Reviewed in the United States on September 6, 2024
It is a quality product and was exactly the same as OEM , just not broken! A bit tough to install only because the way it was mounted requires some effort.
Geekwad
Reviewed in the United States on July 10, 2024
This replacement was close, but NO CIGAR and NOT equivalent to OEM assembly of a 2002 Honda CR-V. The main tank was too SHORT in length by about an inch and the mounting tab would NOT line up with the OEM tank mounting hole. If mounted in the OEM mounting hole, the rear of the tank had NO support and would NOT set inside of the washer fluid level viewing window slot located in the driver's door hinge pillar post. After setting the rear of the tank in the viewing slot of the pillar post, I had to drill NEW mounting hole to secure the front of the tank. CAUTION: Before drilling new mounting hole, check and be sure NOT to push the rear of the tank too far back into the pillar post fluid viewing slot or the front lip of the driver's door will hit the rear of the tank protruding through the viewing window, when the door is opened all the way. Also, the wiper fluid hose ports on the tank water pumps were oriented in different locations from the OEM assembly, but was able to get the hoses connected. Electrically the wiring harness connectors fit as they should. I would have returned this tank assembly had I known what I know now about the imperfection, but it was over 30 days from purchase when installed and I did NOT want to seek another aftermarket manufactured brand, having to do this job TWICE !!!! At the end of the day, the assembly had NO leaks and worked as it is supposed to. I would have purchased a Honda OEM assembly if Honda didn’t price theirs so outrageously HIGH.
Kev Lid
Reviewed in the United States on June 25, 2024
Fits fine, works, no fluid level.
Chuck B.
Reviewed in the United States on December 3, 2024
It’s all good. Only problem I could foresee would be the novice DIYer that would have trouble wiring in the plug for the pump.
B-RAD
Reviewed in the United States on December 24, 2024
Perfect replacement for my broken washer fluid reservoir.
Sam
Reviewed in the United States on October 6, 2024
Good item, has been installed for a while now and it is functional. Would buy products again for a different vehicle.
Tharindu Dhanapala
Reviewed in Canada on October 30, 2024
It’s compatible with Mazda 3 2011. but it didn’t had a provision for install the sensor. other-than that it’s ok.
Juan C.
Reviewed in Mexico on April 11, 2024
ENVÍO DEMASIADO LENTO, TARDO 45 DIAS EN LLEGAR
Recommended Products
