Your cart is empty.
Your cart is empty.At the forefront of the security industry, TRIMAX stays in tune with market conditions, analyzing the demand for more security and producing products to meet that demand spanning markets such as trailer and towing, power sports, marine, RV and bicycles.
Kevin T
Reviewed in Canada on August 29, 2024
I have a drop hitch which makes it difficult to find a hitch with multiple ball sizes. This is a perfect solution and I like that I can easily torque the balls together using the 1/2" insert on the top of each ball.Strong recommendation.
Justin Harp
Reviewed in the United States on August 10, 2024
Work great but the hitch they are for not so good together the balls come loose on the hitch
D man
Reviewed in the United States on July 26, 2024
I can move my wife's trailer with our tractor then flip it over and move mine with little effort.
S Eckert
Reviewed in the United States on September 16, 2023
Everyone talks about how these fit their drawbar but I didn't read about two important things: The included lock washer fits inside the smaller ball's base, and BOTH balls have 1/2" square drive holes in the top of the ball. I used a breaker bar and a torque wrench to tighten them, and didn't need to add spacer washers as others have mentioned. If the threads are too long for you, I'd suggest carefully grinding off the end instead of adding spacers. Think carefully about torque on the threaded shaft if the balls don't seat directly on your mount.
Peter Bellas
Reviewed in the United States on June 7, 2023
Just installed mine and it was just what I needed, a single hitch with a small drop for 2" towing and slight raise for my heavy equipment. I was surprised that the double ball was so hard to find. It seems really sturdy, we will have to see on longevity.Just a note, I have a .75" drawbar which was not enough thickness to get the balls tightened. I had to use a .150" washer on each side to get a proper tighten, so I would say you need a .90" drawbar thickness. Hillman makes a 1" - .150" inch thick, grade 5 washer that fits the bill.
Chris Henderson
Reviewed in the United States on October 24, 2023
These work great on adjustable hitches. Easy to tighten with (2) ½" square wrenches/ratchets.
Jourdan Desjardins
Reviewed in Canada on September 22, 2021
good
Dylan lobb
Reviewed in Canada on February 21, 2021
Great fit
Geoff Spencer
Reviewed in Canada on September 21, 2020
Good value just should have come with the hitch.
ALEJANDRO L.
Reviewed in Mexico on April 2, 2020
buena calidad y resistencia ya lo cale ,, funciona bien y practico ..
CGraves
Reviewed in the United States on September 28, 2017
Hitch ball seemed very well made. Chrome finish was nice. But I could not get the ball to tighten onto my hitch. The balls will only screw together to a certain point as one acts as an acorn nut on the other. And I couldn’t use washers because the lock washer was inset into the ball. Remember the internal set screw is reverse thread (might be obvious to must)
moocowman
Reviewed in the United States on February 1, 2015
Great balls. Easy to install. I like how the ball ends have holes for 3/8 ratchets to tighten. The price is right, too. Only complaint is that the are not marked with the ball size. I know the size, but if someone else not familiar with balls borrows my truck, they may end up using the 2" ball on a 2-5/16" coupler and end up losing the trailer.
Wolfgang Unger
Reviewed in the United States on March 6, 2014
I received this and immeadiately installed it on my Ram 3500 using an adjustable hitch. I was worried about the socket indents and water intrusion to the threads if the socket went into the threaded hole; but was relieved when I saw that the sockets have a bottom so that rainwater will not get to the threads if the 2" ball is up (it has the female socket).One caution...This works great on a higher truck like a HD 2500 or 3500, but a 1500 at factory height with an adjustable hitch could leave you with a ground scraper on slopped entrances, raised RR tracks etc. Other than that, it is a sharp looking setup with the ease of flipping it for a quick conversion between 2" and 2-5/16"! Very happy with it!
Recommended Products
