Your cart is empty.
Your cart is empty.Product Description
Why We Need to Use TPMS Sensor?
TPMS is designed to monitor the air pressure in a tire and send a warning to the vehicle’s onboard monitoring system when the pressure drops below a preset limit. TPMS sensor can help improve ride and handling, reduce stopping distances, and the potential for hydroplaning. Tire pressure sensors can also increase fuel efficiency and extend tire life.
Replace OE Number
F2GZ-1A189-A, F2GT-1A180-AB, F2GT-1A180-BB, F2GT-1A150-AB, F2GT-1A150-BB, GL3T-1A180-AA, F2GZ-1A189-B.
ISINLASSO TPMS Sensor Feature
- Frequency: 315MHZ
- Pressure Monitoring Range: 100 – 900kPa
- Operating Temperature: -40℉~257℉ / -40℃ ~+125℃
- Battery Life: ≥5 years
- Battery Voltage: 2.3-3.6V
- Pressure Reading Accuracy: ±3 kPa
- Installation Type：Snap In
Intelligent Chips
ISINLASSO TPMS Sensor is equipped with a Advanced Chips which supports up to 900KPA transmit strong signal, leakage and more accurate monitoring Range.
Strong Battery
High Performance CR-2450 lasts over 5 Years/60-100.000 Miles，Straight forward replacement for OEM TMPS sensors.
Interchangeable Stem
The Stems adopts High Quality Stainless Steel, can be change and resistant, designed to prevent air Leakage and Corrosion in all Weather
Relearn the TPMS sensor:
- OBDⅡ connector is required：
1. Put the vehicle in P gear, pull the handbrake, and properly install the tire pressure sensor.
2. According to the tire label (usually on the door frame), inflate all tires to their nominal value and let stand for 5 minutes.
3. Starting with the left front wheel and using the TPMS tool, activate each sensor in turn in the order of left front, right front, right rear, left rear and full size spare tire (if available).
4. Turn the ignition switch to the ON position.
5. Connect the TPMS tool to the OBDII interface and write the sensor ID using the OBD learning function.
6. Disconnect the OBD connector.
7. Turn off and then on the ignition switch.
8. Road test at a speed higher than 19 mph for at least 10 minutes to ensure that the tire pressure system works normally (tire pressure light is off).
- OBDⅡ connector is not required：
1. Install the tire pressure sensor correctly.
2. Inflate all tires to their nominal value according to the tire label (usually located on the door frame).
3. Stop for 20 minutes. Then drive at a speed of 16-62 mph for at least 10 minutes. The tire pressure system will automatically learn the tire pressure sensor, all tire pressure warnings will disappear, and the tire pressure value will be displayed (if supported).
ALICE & DAN
Reviewed in the United States on February 6, 2025
good product
Nascar9and19
Reviewed in the United States on February 25, 2025
They look nothing like the picture. The version I bought was supposed to come preprogramed at the factory to work on a 2017 Cadillac XT5 (GM part # 13598773) . They do not work! I cannot use my tool to set the sensor that I installed on the left front to record. The original sensors worked fine before. Just have one original with a dead battery. DO NOT BUY THIS CRAP!!!!!!
Leon D.
Reviewed in the United States on February 18, 2025
The tech at the tire shop that installed it had no problem programming the sensor as it was pre-programmed to my vehicle
Customer
Reviewed in the United States on February 16, 2025
They work ok on my Colorado
Joe Kivler
Reviewed in the United States on February 15, 2025
Worked as supposed to
Jc
Reviewed in the United States on February 10, 2025
Tpms were the exact parts I needed for my Explorer. They came pre programed which was a mayor plus.
Customer
Reviewed in the United States on January 30, 2025
Great alternative to save a lot of money on TPS. Works as well as original. A good buy guys 😁
Alexander quintero
Reviewed in the United States on January 29, 2025
Si fue lo q pedí
Recommended Products