Shopping Cart

Your cart is empty.

Your cart is empty.

TPMS Sensor,433Mhz Tire Pressure Monitoring Sensor Fit for Chrysler Jeep Dodge Ram Replace# 56029398AB(4-Pack)

Free shipping on orders over $29.99

$28.99

$ 14 .99 $14.99

In Stock

1.Size:Four Pieces Sensors


  • 【Pre-programmed and Auto-Relearn TPMS Sensor】The Tire Pressure Sensor is 100% new and come pre-programmed specifically for your make/model/year of vehicle,and AUTO-RELEARN,install sensors on your tires and they can automatically after you drive car for 20-30 minutes
  • 【High QUALITY】The battery can be used normally for more than 5 years, the pressure reading can reach 110 PSI or higher, and the temperature can reach -40~125℃,same as OE quality
  • 【APPLICATION】Compatible for Chrysler:2009-2017 300,2011-2016 Town&Country / Dodge:2012-2016 C/V,2010-2022 Challenger,2010-2022 Charger,2011-2015 Durango,2011-2020 Grand Caravan,2011-2022 Journey / Fiat:2011-2019 500,2014-2020 500L,2016 500E / Jeep:2020-2021 Gladiator,2011-2015 Grnad Cherokee,2013-2021 Wrangler / RAM:2010-2013 RAM 1500 2500 3500 4500 5500
  • 【REPLACE PART NUMBER】56029398AA, 56029398AB, 68241067AA, 68241067AB, 68402371AA, 56029400AD, 68464665AA
  • 【GOOD SERVICE】One year warranty.Our commitment to you is total and we want you to always be 100% satisfied by the quality and efficiency of our service.



Product Description

RENECTIV TPMS SENSOR
9011

RENECTIV 56029398AB Chrysler,Dodge,Jeep TPMS SENSOR

Please Double check the interchange number and compatibility for your replacing

  • Battery Life: ≥5 years
  • Operating Temperature: -40°C + 120°C
  • Pressure Monitoring Range: 100 – 900kPa
  • Frequency: 433MHz
  • Installation Type:Snap In

Package Quantity

4pcs*Tire Pressure Monitoring System Sensor

Replace Part Number

  • 56029398AB
  • 56029400AD
  • 68241067AA
  • 68402371AA
  • 68464665AA
applicable models

HOW TO INSTALL THE TPMS SENSOR

step1

Loosening the tire:

Lift your car, remove tire and the valve stem core to allow all the air to escape, then strip away the tire.

step 2

Dismount the sensor

  • Dismount the tire: Clamp the tire onto the tire changer, and adjust the valve at 1 o’clock relative to the tire separation head. Insert the tire tool and lift the tire bead onto the mounting head to discount the head.
  • Dismount the sensor: With a screwdriver remove the fastening screw and sensor from the Valve stem, then loosen the nut and remove the valve.

step 3

Mount sensor and valve

  • Mount sensor and valve: Slide the valve stem through the valve hole of the rim.
  • Tighten the screw-nut with 4.0 Nm with the help of the positioning pin.
  • Assemble the sensor body against the rim and tighten the screw.

step 4

Mount the tire

  • Mount the tire: Place the tire on the rim, making sure that the valve faces the separation head at an angle of 180 degrees. Mount the tire over the rim.
  • Inflate the tire, check the balance before installing the wheel.

REMOVAL OF THE TPMS SENSOR:

1. Remove the screw that attaches the sensor to the valve stem and remove the sensor.

2. Using a standard tire valve stem tool, pull the valve stem through the hole and discard it. Use a rubber mallet or a block of wood to avoid damage to the rim.

Installation of TPMS Sensor:

1. Insert the new sensor through the valve stem hole making sure the flat side of the sensor is toward the rim.

2. Using a standard valve stem tool pull the stem straight through the hole until the valve stem is fully seated. To avoid damage to the sensor and the rim, use a rubber mallet or block of wood placed between the rim and the tool to make sure the valve is pulled straight.

RELEARN the TPMS sensor:

一:OBD Relearn:

1.OBDII connector is required

2.Confirm TPMS sensors are properly installed

3.Adjust tire pressures to placard value

4.Activate TPMS tool on left front tire sidewall next to the valve stem

5.Repear for RF/RR/LR tires

6.Apply OBD connector to DLC

7.Turn ignition to ON

8.Press OK on TPMS tool to transfer data to ECU

9.Disconnect OBD connector from DLC

10.Turn ignition to OFF then start the engine

11.Drive for at least 5 minutes at 28mph

二:AUTO-Relearn

1.OBD connector is not required

2.Confirm TPMS sensors are properly installed

3.Adjust tire pressures to placard value

4.Activate sensors with TPMS Tool

5.Drive vehicle for up to 20 minutes above 15 mph or until TPMS light is off

TIP:1.In some cases it may help to wait 15 minutes between steps 4 and 5

2. If the system fails to operate properly, check all the installation procedures to ensure proper installation and retest.

ENVIRONMENT
qa

Remoun
Reviewed in the United States on March 3, 2025
work Great no problem
Kathleen Chambers
Reviewed in the United States on February 25, 2025
Working excellent so far, no programming was required for my jeep. Hoping batteries stay up for a bit.
Customer
Reviewed in Saudi Arabia on February 24, 2025
مطابق و عمل بعد التركيب و المشي بسمافة تقريبا 25كم
Brian Jones
Reviewed in the United States on February 20, 2025
Bought these for my 2014 300 and they worked. I drove my 300 for about 5min and the light reset, no program needed.
Mark A. Lowell
Reviewed in the United States on January 6, 2025
Good pricing, but no time to park the vehicle at a shop to have them installed.
Tangle
Reviewed in the United States on January 15, 2025
Purchased for my Fiat 500, and I paid to have them professionally installed. I’ve driven 5 different times now, at length. NO CONNECTION! What a waste. Totally disappointed and angry bc I’ve put time, effort and money into getting these on. I WANT A REFUND!!!!!
dphilmlee
Reviewed in the United States on January 15, 2025
I had these added when I put on new tires. I was dubious because they were so much cheaper than the OEM TPM replacements. (Mopar wanted around $450 for 4 devices). But my worries were unfounded as they are working as expected on my 2013 Wrangler Sahara. My Jeep identified them within the first 100 yards of driving and were calibrated after about 50 miles or so of driving. Highly recommend.
mohmmed a.
Reviewed in Saudi Arabia on August 20, 2024
ممتاز واشتغل ع طول بعد مشي تقريبا ٥ كيلوالسياره دودج تشارجر ٢٠١٤
Ali Hameed
Reviewed in the United Arab Emirates on February 7, 2024
I used it in my 2014 Dodge Durango. Initially, I was worried when it was installed because it wasn't detecting, but without any computer settings, it automatically detected after a 20-minute drive.
R
Reviewed in Canada on December 31, 2024
Installed them on my rims , they worked great. No issues programming them to the car. Great value
Lee
Reviewed in the United States on December 29, 2024
Installed on 2013 ram 1500, Synced up in about a mile no programming needed. The hardest part was breaking the bead on the tire.
Duane R.
Reviewed in Canada on December 2, 2024
Installed, and started working on their own within 10 mins :)
Bryan
Reviewed in the United States on November 22, 2024
2013 Chrysler town and country.Had warning light blinking on the dashWent to local tire shop they said one of the Sending units failed and guoted 100.00 dollars to program and install aNew one.Bought four less than thirty dollars cameNext day had the bad one replaced for 15.00 the new one was already programmed cleared the alarm within aCouple of miles driving. Great
Recommended Products