Your cart is empty.
Your cart is empty.Product Description
ICStation Digital Timer Relay AC 85-265V 110V 220V 2000W 10A HD LED Dual Time Display Relay Switch Panel
- MULTIFUNCTION: support 18 working modes including time delay relay open, time delay relay close, time delay relay open and then relay close, cycle time delay relay open and close working meeting your most demands.
- WIDE WORKING VOLTAGE: built-in AC-DC voltage converter module support AC85-265V wide voltage input can be connected to your home appliances directly easy to use.
- DUAL LED DISPLAY and SLEEP MODE: dual LED display the timing parameter T1 and T2 with sleep mode will automatically turn it off after 10s (need to set), 4 momentary keys to set the parameter, easy to operation.
Working mode
- Time set mode:
- Short Press the SET button and use the up and down buttons to set the time in the Top display(T1) short press the set button to set the time displayed in the bottom display (T2) short press the set button again to save and run.
Timer delay, load use different power supply
- Time unit setting Mode.
- You can set the timer to work in seconds, minutes or hours:
- Long press the SET button for 6 seconds or until P0 is displayed in the top display.
- Press the up down buttons to set the time unit mode in bottom display (T2)
- Top display=P0 bottom display=0 - seconds
- Top display=P0 bottom display=1 - minutes
- Top display=P0 bottom display=2 - hours
Timer delay, load use the same power supply
- P1-0 Load is off until (T1) time counts down to 0 then the load will come on and stay on.
- P1-1 The load comes on as the power button is pressed. After T1 Time the load will go off.
- P1-2 The load is off for (T1)(delay time) then the load switches on and runs for the time set in (T2) then switches off until power switch is pressed to cycle again.
- P1-3 Load is on until T1 Time runs out Then after T2 time runs out the load will come on and stay on.
- P1-4 Load is off until (T1)(Delay) time counts down to 0, then load comes on until T2 time counts down to 0 then the load is off then it cycles again and again-auto cycle.
- P1-5 The load is on until (T1) time counts down to 0 then powers down and after (T2)Time counts down to 0 the load will start working and cycle again and again-auto cycle.
- Done
How can i set the timer delay？
For example, someone wants that the timer turns on for 10 seconds, then turn off for 20 seconds, and cycle.
The setting method is as follows:
1. You can long-press the SET Button enter the parameter setting menu. Choose P0-1 Set T1 10S, then short press the SET button save data. The next step set T2 time 20S.
2. P1-4. After T1 time, the load starts working (T1 timing), and after T2 time, the load stop working (T2 timing), and the above working mode cycle and repeat.
URHC
Reviewed in the United States on February 19, 2025
Works great once you figure out how to program it. I went to the manufacturer website and printed then out. Very simple if you go step by step. Using it to control a vacuum pump on a chamber for degassing epoxy
Philip Schwartz
Reviewed in the United States on July 27, 2022
- construction is flimsy- no surface mount option- poor terminals: too small for even 16 AWG with ferrules, best to use solid conductor- no serial number implies no QA, so caveat emptor- product is simple to use, but not if you try to make sense of the instructions (that are not included)- first timer tested OK, then never worked again: programs ran correctly, but there was never any voltage on the load terminals. Promptly received a replacement that had the same defect and never worked.- Best part of the product is the Amazon product page with dogs and cats. Cute, but everything else is a bust.
Leslie B.
Reviewed in the United States on July 29, 2020
The media could not be loaded.
Scoochie
Reviewed in the United States on November 5, 2020
This timer is able to do many timing tasks since it is programmable. Bright displays make it easy to see in just about any light. Wide range from 1 second to 999 hours. Easy to wire up. The instructions are not very clear at first so I wrote up an instruction sheet that might help if you get confused Timer Easy Setting InstructionsThe upper display is referred to as (T1 or PV) and the lower display is referred to as (T2 or SV).The LED labeled "out" indicates that the relay contacts are closed when it lights up.Time set mode: Short Press the SET button and use the up and down buttons to set the time in the Top display(T1 or PV) short press the set button to set the time displayed in the bottom display (T2 or SV) short press the set button again to save and run.Time unit setting Mode. You can set the timer to work in seconds, minutes or hours: Long press the SET button for 6 seconds or until P0 is displayed in the top display. Press the up down buttons to set the time unit mode in bottom display (T2 or SV)Top display=P0 bottom display=0 - secondsTop display=P0 bottom display=1 - minutesTop display=P0 bottom display=2 - hoursThere are 5 timer sequence modes:Long press again to set the operating mode when P0 is displayed press set to display P1 then press the up down buttons to display 1 or 2 or 3 or 4 or 5 to set the type of timed operation you want.P1-0 Load is off until (T1 or PV) time counts down to 0 then the load will come on and stay on.P1-1 The load comes on as the power button is pressed. After PV Time the load will go off.P1-2 The load is off for (T1 or PV)(delay time) then the load switches on and runs for the time set in (T2 or SV) then switches off until power switch is pressed to cycle again.P1-3 Load is on until PV Time runs out Then after SV time runs out the load will come on and stay on.P1-4 Load is off until (T1 or PV)(Delay) time counts down to 0, then load comes on until SV time counts down to 0 then the load is off then it cycles again and again-auto cycle.P1-5 The load is on until (T1 or PV) time counts down to 0 then powers down and after (T2 or SV)Time counts down to 0 the load will start working and cycle again and again-auto cycle.Done
Carolyn
Reviewed in the United States on February 27, 2018
I found this unit did exactly what it was described to do. My application needs to flash a strobe every 15 seconds. This unit is just right for this task. I set it to go on for 1 second every 15. One of my requirements is low power consumption. The seller did a good job discribing the power usage and through testing it was spot on. It uses 12ma to count down the 15 seconds then spikes to 50ma for the one second on. This is due to the solenoid closing the contacts for that one second. After the one second the contacts release and it goes back to 4ma. The click of the contacts is loud and the display is bright but those were secondary and thus 5 stars. Another item to note is that if your Vcc running the timer goes down to just abouve 3 volts DC, the unit goes into convulsions. The display flickers and the solenoids do not close. This does not mean it is any less quality but you should have a solid 12 volts.Pros: Unit is easy to set. Display makes it easy. Uses low power in count down mode. Wire connection points are clearly labeled and tighten nicely with a small screw driver. Programming stays in unit even after the power is shut off.Con: Loud Display cannot be turned off Instructions did not come with the unit but were sent to me later. I had already downloaded them.
Recommended Products
$46.85
$ 21 .99 $21.99