Shopping Cart

Your cart is empty.

Your cart is empty.

Through Hull Wiring Kit for Kayaks, Thru-Hull Wiring Kits for Wilderness Systems Hobie Installs of Fish Finders, Motors,Lighting Kits etc Kayak Wiring Accessories

4.8 (8) Write Review
Free shipping on orders over $29.99

$8.99

$ 3 .99 $3.99

In Stock
  • Through Hull Wiring Kit for Kayaks --- Through hull wiring kit is perfect for popular removable pods like the Bonafide Kayaks Dry Pod or Wilderness Systems Flex Pod. Kayak Wiring Kit is perfect for run wires through the hull of your kayak or boat, keep clean and water resistant.
  • For Use with Many Different Kayak Accessories --- Through Hull Wiring Kit is perfect for mount fish finders, transducer, lighting kits, motors, battery, and anything involving running wiring through the hull of your kayak or boat.
  • High-Quality Wiring Kit --- The wiring kit is made of high quality Marine grade, smooth edge and good thickness, suitable for most styles of boats, yachts and kayaks.Kayak cable gland reduces clutter by allowing you to hide cables inside your hull.Beautiful appearance.
  • Pack Includ --- You will get 8 rubber inserts with common hole sizes, four blank inserts, two nylon grommets, and two sets of hardware.
  • Customize to Your Needs --- Thru hull wiring kit allow a single or multiple wires or varying cable sizes or using the blank inserts to drill a different hole size than provided or to block off old wiring holes.
  • Buy with Confidence --- Your Satisfaction is our goal.If you have any questions about our kayak accessories thru hull wiring kit, please get in touch with us, Whether it's pre-sales or after-sales, we will give you a satisfactory answer within 24 hours!


Product Description

wiring kit
kayak accessories
kayak

ANK
Reviewed in the United States on March 10, 2025
These work as good as the NAME brand product.
Jesus garza jr
Reviewed in the United States on February 23, 2025
Same as advertised picture
Kindle Customer
Reviewed in the United States on February 15, 2025
Used to put a plug for my motor through my hull of my kayak. Worked great and exactly what I needed. However, I would say get some longer screws depending what your need it for.
Jordan ozier
Reviewed in the United States on January 14, 2025
These work great. I used this kit to install a wiring system for my Motorguide Xi3 (kayak), and installation was easy. I would recommend using a step drill bit for the hole itself. The system is very similar to the YakAttack version, but essentially 1/3 of the price. The large size fits 8 gauge wiring just fine. You cannot go wrong with this for a nice, clean wiring setup.
Ben King
Reviewed in the United States on September 23, 2024
Need a 1 inch bit to drill the hole and I used a 1/16 for pilot holes for the screws. Had to cut the rubber pieces to get the wires through but they close up nice and tight
Torrance Wong
Reviewed in the United States on July 11, 2024
No instructions. You'll need a 1 1/4" hole saw that attaches to a drill.Drill hole. Find the rubber piece you need depending on wire size. Cut a slit from the flat side to hole. Use another rubber half piece to make a loop. Drill a pilot hole for the housing. Install two little screws. (Add silicone if you want).For Old Town Kayak owners, I started with a hole near the PDL/transducer scupper. I had to drill from the inside since I could not get my drill to drill flat from the outside. No problems this way. Second hole was near the side rail for the fish finder. Took my time and took a couple of hours, but a very clean install. I also added some silicone to further seal the housing and rubber.
Mack
Reviewed in the United States on June 21, 2024
They seem to be an inexpensive copy of the yakattack version. Absolutely much cheaper but I dont know that I trust them.
coach
Reviewed in the United States on November 29, 2024
Used these to install my garmin fish finder on my old town pdl 106. They worked perfet with a more than adequate seal! Would recommend.