Your cart is empty.
Your cart is empty.This TCI TV Cable Correct Kit for Quadrajet/Edelbrock/Carter Carburetors ensures the correct line pressure for the best performance and service life from your GM 2004R/700R4 Transmission.
Eugene Baker
Reviewed in the United States on January 19, 2025
Yes correct item for 700r4 on Chevy 350, Edelbrock. But depending on age and originality of vehicle be prepared to modify the bracket to suit any alterations made to the vehicle. Installed onto 71 Chevelle wagon, 2003 350 Vortec, Edelbrock AVS2-650, conversion from Quadrajet to Edelbrock. Had to add an extension bracket plus drill hole for Dakota cruise control cable.
Wasn’t wide enough had to modify otherwise good
Reviewed in the United States on September 3, 2024
Didn’t fit Holley base
Paul Ardolina
Reviewed in the United States on August 14, 2024
Excellent fit and finish.
Gordon A.
Reviewed in Canada on June 25, 2024
It definitely doesn't fit as advertised. It doesn't fit an Edelbrock carb nor will it line up with the carb linkage. Unfortunately I can't return it because I already painted it. I will either have to cut it up and modify it, or consider it a total waste of money. Don't buy this item.
phil
Reviewed in the United States on March 10, 2024
DOES NOT FIT Edelbrock AVS carbs, 100% does not fit. good quality bracket but DESCRIPTION IS WRONG might fit Edlebrock carbs, but not AVS models
iWorkHard4My$
Reviewed in the United States on February 21, 2024
Looks good have not installed yet
221
Reviewed in the United States on January 14, 2024
interferes with a runner in the 2101. well made but doesn't fit. i'll have to cut it up and weld on a second tab to make it work.
michael zalesky
Reviewed in the United States on September 26, 2023
Took off a Holley carb and went back to the original GM style 4 barrel, qjet so we needed a different bracket than the Holley. Quick ship, next morning it was on my porch. Installed and worked great.
Mike
Reviewed in Canada on June 3, 2023
Fits good looks like it will work well project not finished yet
MykDelta
Reviewed in Canada on August 17, 2022
I swapped a th200 trans for a built 700r4 I only realized as I got going that I would need a bracket like this. Fortunately I found the tci one on here and it works great only cost $55 at the time. My shifts are crisp and everything works great.
Mark Rust
Reviewed in Canada on September 3, 2021
After waiting a very long time for this bracket the holes did not line up like advertised. Had to cut and modify.
Jeff
Reviewed in Canada on September 15, 2019
Works well for quadrajet carbs too.
Ian M.
Reviewed in the United States on November 19, 2019
Not compatible with Edelbrock 1406 and Edelbrock Performer manifold.First problem: must use inner bolt holes on carb. About half of the Edelbrock manifold allow this. Luckily mine was one of them, yours might not be.BUT... once you get past that hurdle, you’ll find that the bracket won’t clear the intake on the back side unless you’re using a riser.THEN, you’ll find that even with a riser, the geometry of this bracket will be waaaayyy off track. And yes, I have a geometry corrector installed on the carb itself. Bracket locates cable about an inch too far inward.AND FINALLY, you’ll discover that you can only use this bracket if you’re using a cable actuated throttle pedal. If you use a throttle rod and linkage, like I do, the rod will not be compatible with this bracket. You may be able to cut off the upper part of the bracket to make this work, but I opted to return this item instead due to all its other flaws. This is a steaming pile of junk.Most other reviews I read online only mention the problem with the inner bolt pattern. I hope this review steers people clear of this item who think that’s the only problem with this bracket.
Recommended Products
