Your cart is empty.
Your cart is empty.
Stanbroil Fire Pit Gas Burner Spark Ignition Kit will turn your manual ignition fire pit, fireplace, gas burner into an easy to start push button ignition. This battery operated igniter will cause a spark to ignite the gas when you depress the button. The key to a good installation is the ground. You must screw igniter bracket solidly and directly to the burner pan. Keep the igniter area relatively clear of embers, rocks, fire glass ect. You can create a void around the igniter using a screen. This void will fill with gas and ignite much easier than an igniter covered in fire glass, ect. The stainless steel face plate will give you a professional mounting for both your push button as your chrome keyed shut off ball valve.
Tips for installation
Run both wires up through the pan from the bottom using any pre-existing hole. Mount the sparker close as possible to to one of the outer gas holes. The key to a good spark is a good ground so make sure that you sandwich one wire between the pan and the bracket. The other ends connect to the push button block. Insert the battery and push the button.
TAD
Reviewed in the United States on September 12, 2024
Per their installation video, there's a part missing from this kit.
Ken
Reviewed in Canada on August 7, 2024
Works good but could use a bit more variance on the flow
Chris R
Reviewed in the United States on July 11, 2024
Overall, I found the unit well designed with some nice features to handle various install situations.I've uploaded some photos and two videos on the ignitor focusing on the box I built since I couldn't mount it to the actual fire bowl because the bowl is solid granite.A few topline thoughts:1. The unit itself is well-designed. For example, the ignitor button unscrews from the front to make it easy to change the battery when needed.2. You'll notice that the metal bracket holding the ignitor button and the valve on/off control is a right-angle piece of metal with holes on the face to mount it that way and the base if needed. In my situation, I just needed the face plate, so I cut off the base part using my Dremel so it wouldn't get in the way. That is why you don't see it in my uploaded photos.3. One thing not obvious is that if you unscrew the round trim where the on/off key goes and undo one screw in the back, you can separate the valve from the faceplate. This is handy during installation as it makes it easier to mount the faceplate and separately ensure the gas lines to and from the valve are installed to the proper tightness.4. Before laying your gas line to the ignitor, ensure you don't have to upsize your gas line from the meter to provide enough flow to the burner. Given the distance, I had to increase mine from 3/4" to 1", and then I just used a reducer to connect the line to the ignitor. The distance doesn't matter at that point, and if you have enough pressure to that point, you will be fine.
Christy C
Reviewed in the United States on March 29, 2024
The media could not be loaded.
Marco Bousquet
Reviewed in Canada on November 26, 2024
Excellent produit qui semble faire ce qu’on attend de lui
Jose
Reviewed in the United States on October 28, 2024
Good
MsTcup
Reviewed in the United States on September 10, 2023
Had professionally installed. Worked beautifully on first use then the Igniter quit working after first use. Installed fresh batteries to no avail.
Anderson
Reviewed in the United States on August 19, 2021
This was exactly what we needed to complete our project. With a little extra ingenuity I was able to drill a hole through one of our cement bricks and mount this. I did need some PVC sprinkler parts to extend the valve from the finish chrome piece to connect it. Worked well.
Jessica M Rittenhouse
Reviewed in the United States on July 29, 2021
5 stars all day! This is a mounted valve panel with a built-in ignition clicker. Not a regulating assembly. Know that going in! Yea, I can turn down the keyed valve and throttle my propane, but that’s just fine and what I expected.I bought this assembly to go along with the Stanbroil 6” x 60” fire pit tray/insert. I hard plumbed it underground to our tank that also feeds our outdoor kitchen. Zero problems whatsoever. Pretty sure the negative reviewers are just not familiar with common gas plumbing. In any event, this is a legit setup for the price. I will add though- the air mixer body does not come with your fire pit insert, nor does it come with the ignition panel. If you’re burning propane, you WILL need this. Don’t sweat it bro- $11…All things considered, I’m still wondering why it comes with a 4” - 90° return on the stainless panel. I cut that off with a skinny wheel and shaped it off with a flap disc so i could face mount it on my fiber cement siding. Associated pictures are for the beta run.Net effect… I’ve got a best friend that works in HVAC; he told me he couldn’t beat that number on a Napoleon unit.Go for it.
stephen ondrik
Reviewed in Canada on March 30, 2021
I retrofitted a firebowl tht was converted from propane. The burner was of course the cheap kind. So I bought this control along ith the stanbroil control and I could not be happier. The only thing I did not like was the ignition. I needed to bend it to be closer to one of the ports on the burner. Once I did that it works flawlessly.
Matt Churchill
Reviewed in Australia on January 17, 2021
Awesome product and delivery time
Greg M.
Reviewed in Canada on September 5, 2020
Exactly as described, great quality, I'm very happy with this purchase.
Simon
Reviewed in the United States on April 28, 2019
Quality product but I couldn't get the igniter to work with my Liquid Propane setup. You'd have to try to bend the 2 prongs so that they are hovering very close to one of the gas pin holes of your burner ring. Instead I bought the FPK Push Button Ignition Kit from Woodland Direct, because it is a single prong igniter that creates a spark between the prong and the fire ring. Then I used a Dremel to widen the hole in this bracket in order to mount the other Igniter button in it. Turned out good. The gas valve of this Stanbroil product is excellent, and this Stanbroil metal bracket is perfect for mounting to your firepit.
Recommended Products
