Your cart is empty.
Your cart is empty.Product Description
PACKAGE INCLUDING:
- 10 Sets of Universal Heavy Duty Undermounting Sink Clip Kits for Kitchen Marble Granite Counter-top Bathroom Vanity Undermount Sink Installation or Re-installation or Repair
APPLICATIONS:
- Safe and Suitable for Under-Mounting Porcelain Sinks and Stainless Steel Sinks in Any Size ( Better Alternative as Undermount Sink Anchors )
MATERIAL OF CONSTRUCTION:
- Zinc Plated Stainless Steel
_________________________________
INSTALLATION INSTRUCTIONS:
- Please note, the more clips installed for you sink, the more secured sink installation will be. Commonly 8 to 10 sets.
- Thoroughly clean up the area of the sink underside panel surfaces where the clips will be installed.
- Use stronger and thicker putty type epoxy or 100% silicone or liquid nail and generously apply to perforated bottom base of the kit.
- Firmly press kit bottom base of into the epoxy or silicone and make sure to squeeze epoxy or silicone come through the holes of the base.
- Wait until the epoxy or silicon securely and firmly sets before installing sink with brackets and wingnuts.
- No worries about imperfect positioning of the sink, you can adjust sink position after installation.
_________________________________
PRO TIPS:
- Any waterproof Epoxy resin, liquid nail or 100% silicone can bond the sink clip bases to the underside of the countertop surface.
- Customers report that using EPOXY might be the best choice for bonding.
- Wait a few hours to completely curl the attachment area to be fully bonded.
- Assembly your sink drain pipe, drain stopper and faucet after the sink installation is completed.
*NOTES:
- This under-mounting sink clip set works with epoxy resin, liquid nail or 100% silicone for bonding. However, the aforementioned adhesives are NOT included in the kits ).
_________________________________
thomas r nelson
Reviewed in the United States on February 3, 2025
What’s some five minute epoxy this thing works miracles
Byron Brunson
Reviewed in the United States on January 4, 2025
I found out the hard waay the contracters didn't install the clips for my sink, eventually the sink fell full of water. these clips did the job. Could not find them in hardware or lowes or HD. Thanks amazon for carrying these.
Christopher J Lynn
Reviewed in the United States on August 26, 2024
wORKED GREAT
NeedMoreTech
Reviewed in the United States on July 8, 2024
I guess working upside down is always going to get messy, but this product could’ve done a better job helping with the install. Ultimately, once installed, it seems to be supporting the weight of my sink (of course there’s already epoxy between the sink and the countertop). But these give a sense of extra secure. But what a mess! The open slots allowed epoxy to drip everywhere and the product doesn’t provide any way to hold the clips in place while being installed.
Tracy Hoffmann
Reviewed in the United States on June 7, 2024
We needed to replace a kitchen sink and found that there were only four brackets on the old sink. We ordered these and they were a perfect solution. The new sink went in without a hitch and we still have a few brackets left over.
CG
Reviewed in the United States on May 12, 2024
Easy to install, made to hold a bond and keep your sink in place.
Retired Engineer
Reviewed in the United States on May 25, 2022
I was hoping that these clips would work for me but they didn't. I sanded the underside of my granite countertop with an orbital sander to get a clean surface for better adhesion then clean these areas with acetone. I used PC Product PC-7 epoxy suggested on Anazon product page and waited 48 hours with temperatures between 70 and 80 F to make sure the epoxy was fully cured. The 7 studs that I installed felt pretty secure to the granite surface before putting on the wing nuts. I was able to attach the stainless steel sink in place by tightening the wing nuts. However, when I put some pressure on the sink to check the installation some of the clips began to separate from the granite. I was able to pull out the remaining clips with little effort (see attached photos). Note that I smeared the epoxy that was squeezed out of the holes to the edge of the plates to gain additional adhesion. The epoxy didn't seem to bind to the granite surface for some reasons. I gave a 3 rating because the clips themselves could have worked if they were securely attached to the granite.
Jerry Z
Reviewed in the United States on December 15, 2022
At first I am also concerned about whether it will hold. 24 hours after applying JB weld epoxy on the anchors, they bond well with the quartz surface. To avoid the clip breaking the studs away from the surface due to too much leverage, I placed the clip on the bonding foot of the anchors, so even if the wing nut screws in, the force to pull away from the surface balances itself with the pressing force towards the surface. One thing to watch is to avoid getting the epoxy on the anchors threads, it is hard to screw in once the epoxy cures. I have to scape the epoxy off the threads to screw in.Great solution for under mount sink installation. The users failed with the product probably didn’t use the right adhesive or installed improperly.
Customer
Reviewed in Australia on October 31, 2022
Fast delivery...great seller...only seller on internet with this product....only dislike is metal seems quit thin...5 star if material was a little thicker
Richard Traub
Reviewed in Australia on July 19, 2021
They worked great, combined with epoxy glue it solved my stone benchtop dropping kitchen sink issue
David Hamilton
Reviewed in Canada on March 30, 2021
Was easy as pie to install
Vlad
Reviewed in Canada on December 25, 2020
Very good product.I used cold weld to attach the clips to the underside of a quartz counter, the clips are great and it's a pleasure to work with.Shipping was a bit long, but did the job.Satisfied and I think this product is recommended to anyone!
ray gill
Reviewed in Canada on November 23, 2020
worked great
Recommended Products
$26.95
$ 11 .99 $11.99