Your cart is empty.
Your cart is empty.This is a pop-up ball joint rod that fits Ez-Flo and ProValue faucets. It comes in a 6-1/2 inch length and is easy to replace.
Cheryl
Reviewed in the United States on February 17, 2025
Fit perfectly as original and easy to install. Works great.
Michael Morris
Reviewed in the United States on January 16, 2025
Fit my sink perfectly! Nice Quality. Could not find this part at local big box (HD) store.
Dan
Reviewed in the United States on June 30, 2024
This item got the job done and was super easy to install, my only complaint was the quality of the piece that's supposed to keep the bar locked in/to the pusher, it isn't the strongest and if you pull on it too hard it pops it off again.
Customer
Reviewed in the United States on June 27, 2024
Perfect fit for my sink drain and works as it should!!
Customer
Reviewed in Canada on May 13, 2024
Cheap and works fine!
Robert
Reviewed in the United States on February 11, 2024
Wasn't a perfect replacement as far as the ball size but as long as the plastic pieces are set over the ball, there will be no leaks and it will work just fine. Overall happy because it sorted out my
M3 Pete
Reviewed in the United States on November 14, 2024
Needed to replace a 15mm ball rod and this was a perfect fit. I took off a star because I wish these came in stainless steel, as these chrome plated steel ones rust out. But I'd buy it again.
Sim
Reviewed in Canada on January 20, 2024
I like that it’s a standard size. Still does the work at such a little price.
Edward W.
Reviewed in Canada on June 7, 2023
Fits perfectly as replacement to our broken joint rod for the sink drain cover to lift up/down. Great as a replacement for repair purposes. I bought two just in case another sink drain decides to break apart (due to rust, they actually can break apart/rot/rust out.
J. Donch
Reviewed in the United States on May 8, 2023
An exact replacement for a builder grade pop-up ball joint rod at a very affordable price. For the price of ONE at the local store, I can replace all 4 in my two, double lavatory sinks. The ball is 15mm/.59 inches and the rod projects 1.4 inches from the ball. Originally, like others have mentioned, I thought the rod was too long as it initially rubbed against the tail pipe. thinking I might have to cut/grind it down, upon taking it out again, I realized that when putting it on, the inside plastic seal had fallen off. Once replaced, it fits/operates perfectly. Note that it comes with TWO plastic seals. One should be placed on each side of the ball to seal and provide smooth operation of the ball.
Debbie
Reviewed in Canada on November 27, 2023
Works as intended, and easy to install to replace the original.
Dr. Zen
Reviewed in the United States on October 29, 2023
The faucets were installed when my home was built over 10 years ago. It's been a while that it doesn't work as expected, whenever I pull the rod up to retain the water, it just doesn't stay there. I have been reminded to replace them (it's over 10 years after all), but that would be a lot of work, some money involved, and I am not that handy. Until I got this part! After I replacing this the faucet works just like what it was in the past. The washer and the ball and the rod crossing the ball were worn. Just a few dollars and less than 10 mins I think it will work for quite some years.By the way, I totally recommend everyone to buy a few extra in case the product is out of stock in the future given the price is so low (compared with new set of faucet).
jeffree
Reviewed in Canada on May 10, 2021
As you can see, the dia of the rod is little smaller than the original one, so is the pivot ball. But finally it seems working well with the two washers provided. Also I used the original plastic nut instead of the slim metal one. I fixed my lift rod with ~$7 so I am happy with it.
Recommended Products
