Your cart is empty.
Your cart is empty.Winch style crank allows the shooter to easily cock their crossbow. The adjustable butt stock mount fits the fang 350, Vector 310, ds rdx 365 and the rdx 400.
samantha m.
Reviewed in the United States on August 4, 2024
Worked great
JamesinPA
Reviewed in the United States on October 3, 2023
Parker is no longer in business so getting a crank for it was impossible. I found this and it looked close enough to universal and I could make it work. I was right, it was nearly an perfect fit for the buttstock of both of my Parker crossbows. Works great too.
604 Mark
Reviewed in Canada on February 24, 2019
I bought PSE Speed Loader Crank for my Sniper Elite Whisperer 370 crossbow. It is a bit wider than the stock of the Sniper Elite Whisperer, so it curve to the crank side, and crank hits the pulling cable. I made the insert from the lid of the detergent bucket and glued it with hot melt glue that works with plastic as well. Now it works like a charm.I agree with some comments that it is better to shorten the stock to “0” position before cranking, and I also shortened the cable to fit exactly Sniper Elite Whisperer 370 stock at “0” position. This speeds up cranking a little bit.
Cindy Brammer
Reviewed in the United States on June 1, 2018
Like it. Sighted in my Sniper 370 with it. Deducted 1 star because a little wobbly on the Sniper 370, but you have to realize it wasn't really designed for the 370 either, it simply works.
Aaron Gaudette
Reviewed in the United States on January 13, 2018
It's not very sterdy on a center point sniper 370. It's easier of just using the rope cocker. It feels like the thing is going to break.
AmyDenae
Reviewed in the United States on January 27, 2017
Purchased for my sons center point sniper. He was having a hard time drawing back. This did the trick even though it's not made for it with alittle modification and good to go. Used kindles rubber tape strip on sides of stock to snug it up.
spud
Reviewed in the United States on July 6, 2016
I bought this for a recently purchased Center Point 370 crossbow. While this is intended for PSE Xbows, I thought I would try it as Center Point only provides a rope cocker and my physical disability is painful to even use that. This is adjustable for the vertical dimension and the bottom half fits the butt pad of the Center Point 370 perfectly. The top half is a little too wide so I glued a 3/4 inch long by 1/2 inch wide by 1/8 inch thick rubber strip on each side inside of the top half and tapered the top end of the rubber strip and now it fits snug. Now it works as intended. I shorten the stock length adjustment on the 370 for cocking so it was not putting the strain on just that pin .When it gets to the almost fully cocked position, you have to watch that the left side pulley doesn't interfere with the dry fire lever. With this a person with limited physical capability can cock the Center Point 370. It is slower than a rope device but that is not the point. Follow the included instructions. I saw a you tube demo where it was obvious he didn't read the instructions. I love my 370. Very accurate, has features found on bows costing lots more $.
Charles M. Jensen
Reviewed in the United States on June 20, 2016
Would not work with my crossbow
Ken
Reviewed in the United States on April 20, 2016
This is supposed to fit the PSE Fang crossbow. the stock mount is however too wide. The length can be adjusted but not the width. Once it is attached according to the instructions and you begin to crank it it begins to roll towards the side of the crank. If the crank is on the right it begins to roll off to the right as you crank and to the left if the crank is on the left. When I was cranking it it almost came completely off which would have caused a dry fire and possibly ruining my new Fang. It was a very tricky maneuver to release it and slowly crank it backwards to release the tension. This may fit other bows but it does not securely mount on the Fang. Thankfully Amazon has a good return program so I could return it.
Recommended Products