Your cart is empty.
Your cart is empty.Permatex's Permapoxy Black Plastic Weld is a structural adhesive designed for general purpose bonding of a wide variety of materials. Black Plastic Weld forms a tough, durable bond to most plastics, composites, ceramics, and wood in any combination. It is a fast-curing product with gelling of mixed adhesive in 5 to 6 minutes and fixturing in 9 to 10 minutes. Bonds hard and soft plastics to specified surfaces, and requires no primers. Sets in five minutes at room temperature, with a temperature range of -60 degrees Fahrenheit to 250 degrees Fahrenheit (-51C to 121C). Permanent strength up to 3500 PSI, and gap filling to 0.125 inches. This epoxy is water resistant, with good chemical resistance. Suggested Applications: Bonds rigid materials including ABS, acrylic, fiberglass, FRP, glass, PVC, SMC, steel, styrene, vinyl, and wood. NOTE: Permatex Black Plastic Weld will not bond polyethylene and polypropylene plastics.
Brad W.
Reviewed in the United States on February 18, 2025
Easy to use, easy to mix, and easy to apply. Set up in about 15 minutes and repair seems sturdy. Not sure yet how well the cap seals the container once opened but hopefully it wont harden as the unmixed components sit. I'd buy it again if needed.
Customer
Reviewed in the United States on January 30, 2025
Product hardens great but does not work because it doesn’t bond to other plastics.
Fish church llc
Reviewed in the United States on January 27, 2025
I had worn some holes in my otter sled tub and it patched them very well. You could barely tell i had used it. Repaired the cracks seamlessly. There isn't a lot in the package but the quality seems very good. Would buy again.
Garry
Reviewed in the United States on September 9, 2024
Works well but storage life very short.
Alex Reshuan-Nieto
Reviewed in the United States on September 13, 2024
I've been searching for an epoxy for plastic. THIS IS IT.I use it to fix the fairing of my motorcycle. Other epoxies would get hard but they didnt stick to the plastic. THIS DOES. Works wonderful and gets hard.It sets really fast . Not much time to work on it. Probably 7 minutes. But i dont care. This is the bets product for plastic. It cures in a few hours
Raziel
Reviewed in the United States on July 8, 2024
Some bumper clips broke and part of the actual bumper would flap while driving. I took it to a local body shop and of course they wanted to replace the entire bumper for $1,700. I purchased this as a YouTube recommendation and follow their instructions to repair the bumper clip. 20 minutes later the clips are repaired and the bumper is holding place. The instructions are easy to read and easy to follow. You do have to work rather quickly as it begins to harden.So far so good..it's holding up really really well in this Florida heat/weather.Now I'm looking for other things to "plastic weld"!
joe boffo
Reviewed in the United States on December 19, 2024
I have been using this for years now and it works fantastic. I have used it on hard plastics and PVC pipe but it will work on many other materials and when its dry it keeps its bond and I have never had something re-crack or break once applied. Make sure to keep from freezing and follow directions. Most important make sure surface to be bonded is properly prepared or may not bond correctly. I hope no one changes formula on this and ruins it.
Chris Mc
Reviewed in the United Kingdom on November 11, 2024
Need to fix a broken front bumper tab , this foes exactly what it says , worth the money
Olajanik
Reviewed in Germany on March 20, 2020
Bardzo trwały i szybko wiąże, tubka prosta w użyciu, jedyny minus to podwójna kapka, która nie trzyma się po nałożeniu i trzeba czekać aż klej ją złapie
R. Nada
Reviewed in the United States on November 4, 2019
This stuff works great on ABS plastic. I used it to repair a cracked radiator fan shroud, which has split about 3/4 down the side. I had some reservations, based on some of the other reviews - as well as a review I saw on YouTube by the Project Farm guy. However, I decided to give it a shot and see how it worked. I started by cleaning the plastic shroud with isopropyl alcohol, then used a little brush to make sure the plastic was clean.I then mixed the glue on a paper plate using a little popsicle stick. I think the trick to this glue is to really mix it well. I read a lot of other review were people were complaining that the glue didn't come out evenly or it didn't work. In my case, the glue came out just fine, but if one side or the other is coming out al little more, you just have to shift the pressure on the plunger over to the other side to help equalize things.** Very important: make sure you remove the built in stirring stick from between the plunger part, otherwise the it's hard to get the glue to come out smoothly.I mixed the glue up really well.. all back and forth, sideways and up and down. Then used the stick to spread it over the ABS plastic of my radiator fan shroud. I used 2 or 3 applications, but even just the first one did the trick. I was totally dry in about 30 to 45 minutes when I checked. It even glued to the wood (the stick I used to mix) and the paper plate. Those two ended up bonded together for life. So it's pretty impressive how fast it setup and how well it worked on the plastic. After applying the 3rd coat, I put some force on the plastic shroud and it didn't budge.I have to give this stuff 5 stars. It setup quickly and seemed to bond very well to the ABS. I wasn't expecting it to work as well as it did actually. It's a plus that it's a nice solid black color also, as it matches black plastic parts a lot better than some of the other glues out there.
Recommended Products
