Shopping Cart

Your cart is empty.

Your cart is empty.

NOYITO 1kg 5kg 10kg 20kg Load Cell and HX711 Combo Pack Kit - Load Cell Amplifier ADC Weight Sensor (5kg+HX711)

5.0 (2) Write Review
Free shipping on orders over $29.99

$7.50

$ 3 .99 $3.99

In Stock

1.Size:1kg+hx711


About this item

  • Load cell：Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurate measures forces from 0-5kg/ 5kg /10kg /20kg.
  • HX711 :This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller (like an Arduino or Raspberry Pi).
  • Load cell specs: 22 cm (8.5 in) wire leads pre-attached. Dimensions 13.5mm high, 13.5mm wide, 76 mm long (0.5 in x 0.5 in x 3.15 in). 4 mounting holes, 15 mm spacing on each side. One both holes tapped M4 thread, the other side both holes tapped M5 thread.
  • HX711 specs: Operation Voltage: 2.7V-5V ; Operation Current: < 1.5mA ; Selectable 10SPS or 80SPS output data rate ; Includes breakaway headers for connection, soldering required.
  • Please choose the correct specification before buying. (A total of four specifications).Please refer to the picture on the left of this page for the product wiring diagram.



4.1 out of 5 stars Best Sellers Rank
  • #150,286 in Industrial & Scientific (See Top 100 in Industrial & Scientific)
  • #30 in Force Gauges
 Is Discontinued By Manufacturer No Date First Available March 14, 2018 Manufacturer NOYITO

Description
Load cell - Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg/ 5kg /10kg /20kg.
HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any microcontroller (like an Arduino or Raspberry Pi).

HX711 specs:
Operation Voltage: 2.7V–5V
Operation Current: Selectable 10SPS or 80SPS output data rate
Mounted on breakout board
-ncludes breakaway headers for connection, soldering required

Connections:
Red wire to E+
Black wire to E-
Green wire to A+
White wire to A-

Package Included:
1xLoad Cell and HX711 Combo Pack Kit


jacob
Reviewed in the United States on November 20, 2020
My load cell was dead on arrival. im sure most of them are fine, i just probably got a dud. gonna have to buy another one.
Stephen
Reviewed in the United States on April 23, 2018
The wires are thin and brittle. The white wire looked like it was bent so hard that the sheathing was almost coming off. All the wires are close to 12 inches except the red power wire. It was only an inch long and VERY difficult to work with. It works off and on as long as I wiggle the wires once in a while. I think the wires are damaged inside their insulation because I have remade all the connections several times and it works as long as I don't move it as soon as I do it stops working. I would really like to get a working model of this product. If you are looking to by I would recommend finding a better model.Edit: 4/28/18I arrived home tonight to find that I have received a replacement model of this product in the mail today. I have not tried it yet but I am excited to see it work properly! It seams to be in better condition then the last. All the wires on my replacement are all the same length and seem solid.