Your cart is empty.
Your cart is empty.Product Description
- ●Making Material: The rolling lathe live center is made of high quality metal, this rolling lathe live center has high hardness and is durable in use.
- ●Working Performance: The rolling lathe live center is professional manufacturing for good working performance.
- ●Scope of Application: The rolling lathe live center is suitable for high speed lathe, CNC lathe, and general manual lathe.
- ●Long-Term Practical: Features excellent and liquid proof seal while the rolling live center has long service life.
- ●Characteristic: There have high accuracy, high rigidity and high wear resistance on the rolling lathe live center .
Colleen
Reviewed in Canada on April 29, 2024
Makes lathe work easier
RB
Reviewed in the United States on October 1, 2023
I turn a lot of green wood for blanks that I slow cure for projects a couple of years down the line. This center has seen countless hours of off balance turning when I'm shaving off bark and branch nubs to make anywhere from 3" to 12" diameter blanks up to a couple of feet long. No complaints as it never gets warm and it always takes a full load with no issue. I use it for finished projects as well and the long point lets me get in close for small diameter work as well. I've seen complaints that it isn't concentric but the point is ground to be nicely centered, it's an optical illusion that happens because of the way it's ground. it can appear non concentric but it is if you pay attention to the tip, not the grind marks.Would buy again.
Brett Stuckey
Reviewed in the United States on January 17, 2023
Strong sturdy and thin live center.
Buy it all!
Reviewed in the United States on September 15, 2022
Good product, works as advertised.
Customer
Reviewed in Canada on March 28, 2022
First issue. The MT length is/was too short to engage the stop in the rear of my metal lathe tailstock. As It was impossible to eject the center, I had to disassemble the tailstock and knock it out. Drilled and tapped the end of the center and installed a button. Now it ejects okay. Second issue. There is over .008” runout, you can see it with your eyes. Never found this out until I went to use the center. Absolute junk
David
Reviewed in the United States on October 26, 2022
Very nice live center. Very smooth and solid.
SYJ
Reviewed in Canada on April 16, 2022
The media could not be loaded.
Rob2000
Reviewed in Canada on August 28, 2021
Nice live centre, Works as it's supposed to.
Scott K.
Reviewed in the United States on August 19, 2021
Great live center when you need a smaller point or more access to the end of the turning you are doing. For most wood turners, get the big 60 degree live center first, I use it much more often. Great second or third live center though.
Charles
Reviewed in the United States on May 31, 2021
very sharp point. had to stone it down to avoid impaling my arm. hold true no taper issues for out of concentricity. main problem that I have noticed is it does tend to heat up pretty fast on a lathe. mainly because I am turning metal and I need a tight fit to keep it from moving.
Bruno isabelle
Reviewed in Canada on March 8, 2021
For my friend machine shop and he love it
Day
Reviewed in the United States on November 20, 2020
Needle sharp and runs true.
KC in USA
Reviewed in the United States on November 14, 2020
The delivery was ahead of Amazon's prediction. According to my dial indicator, the runout on this live center is really about .2 thousandths. Hard to believe as my other live center is about 26 thousandths. I expect my work will run a lot truer now. The only fault I have with this is the MT2 is a bit short keeping the center from popping out of the tailstock when it is fully retracted. I put a couple of threads in the drilled taper end and added a screw there to avoid the problem. Good live center for turning close to the end of the work.
Recommended Products
$49.95
$ 24 .99 $24.99