Your cart is empty.
Your cart is empty.Product Description
Product description R8732P Size: 32", Finish: Peened Features: -Product Type:Grab bar -Weight Capacity:Over 400 Lbs -Adjustable:No. Specifications: -ADA Compliant:Yes. Dimensions: -Overall Height - Top to Bottom:3.5 -Overall Depth - Front to Back:3 -Overall Width - Side to Side:12 -Overall Width - Side to Side:18 -Overall Width - Side to Side:24 -Overall Width - Side to Side:30 -Overall Width - Side to Side:32 -Overall Width - Side to Side:36 -Overall Width - Side to Side:42 -Overall Width - Side to Side:48 Moen SecureMount peened 32-Inch grab bar has a peened finish. It is ADA compliant and comes with a limited lifetime warranty. A Genuine Moen Product. Moen is dedicated to designing and delivering beautiful products that last a lifetime. Moen offers a diverse selection of kitchen faucets, kitchen sinks, bathroom faucets and accessories, and showering products. Moen products combine style and functionality with durability for a lifetime of customer satisfaction.
From the Manufacturer
Moen SecureMount peened 32-Inch grab bar has a peened finish. It is ADA compliant and comes with a limited lifetime warranty. A Genuine Moen Product. Moen is dedicated to designing and delivering beautiful products that last a lifetime. Moen offers a diverse selection of kitchen faucets, kitchen sinks, bathroom faucets and accessories, and showering products. Moen products combine style and functionality with durability for a lifetime of customer satisfaction.
Richard Weinberg MD
Reviewed in the United States on February 21, 2025
These Moen grab bars are nicely made and very, very helpful for older people and all those with any balance or other problems that affect them while entering, in or exiting the shower/bath.
LATITUDES
Reviewed in the United States on January 28, 2025
Excellent and because of its length, it fits 16 inches on-center, the standard for most walls. Others, of greater length, must be installed at an angle to do the same.
KH
Reviewed in Canada on September 24, 2024
Too easy to scratch. Scratched during installation with no apparent way of removing the scratches.
Matthew
Reviewed in Canada on July 4, 2024
Much more solid feel than some other thin grab bars. Requires drilling through tiles into studs.
NKJ
Reviewed in the United States on March 30, 2024
This grab bar is very secure when attached to wall studs. The smaller circumference and peened surface make it easy to grip.I installed this grab bar myself with my husband double checking my measurements and stud markings. We installed it horizontally at 34" from the floor beside a toilet. To install, mark both sides of each stud with blue painters tape, because stud location must be exact in order to use two screws at the top and one at the bottom as recommended in the included instructions. Based on previous reviewers' dissatisfaction with the included screws and another reviewer's recommendation, we purchased six #10 stainless steel, pan-head screws for our installation. At $0.89 each, the screws added about $6 to the overall cost, but worked perfectly. We predrilled a 1/8" pilot hole for each of the six #10 screws and screwed them in with a power screwdriver.After about 6 months, we could not be happier with this grab bar and plan to install one in a second bathroom soon.
DON STUART
Reviewed in Canada on January 20, 2024
grab bar used for holding on to from getting up from toilet
WWC
Reviewed in the United States on August 17, 2022
Hundred year old house, what is behind bathroom walls? Some suggest tearing out hole in adjoining room to find out? No way. It took some time to figure out this project so maybe it’ll help someone else.The main difference was using 4 heftier screws for each grab rail ( #12 2 ½”stainless steel screws, pan head, sheet metal) carefully placed in studs rather than the 6 provided with possibility of poor placements and some reviews complaining about screws.Reasons for making installation change besides using strong studs: (a) distrustful of evenness of inside surfaces behind these walls (lath & plaster) and meeting clearances for various toggles/anchors that require large holes. (b) How easy it is to get 3 screws in each end of Moen bracket or proper clearance for an alternative anchor? Hold a 2 x 4 under bracket (Pic 1), the Moen plan will work if you have an almost perfect center mark for the stud since holes maybe close to the edges.The blue tape shows mapping a stud and bracket placement with center approximated from stud finder (Franklin ProSensor 710) & 4ft level (Pics 2, 3, 4). Stud finder is not designed to do this for acrylic wall but it gives a signal that something solid is behind the wall and approximate points. Select the center of the signals. Vertical measures increase confidence in findings (do more than 2), the level held vertically showing how well the center marks line up. Looks like a stud there?The vertical grab rail was more difficult. The hole under the bend looks somewhat inaccessible. After marking the stud and grab rail location, the hole was carefully marked, and without the bracket, drilled with a 1/8” bit to double check for the stud followed by the pilot hole (pilot bit size for # 12 screw = screw shank diameter minus screw threads, 3/16—try pilot out in scrap wood).After finding stud and marking hole, without the bracket in place, screw in the #12 screws (use screw lubricant, e.g., wax) and temporarily back them out. For holes under the bar, an inexpensive ratcheting offset screwdriver with #2 Phillips bit works (Pic 5). These holes can go in part way with an electric screw driver & extension if you do them 1st, then tighten what’s remaining with the ratcheting screw driver. A small scrap of wood held on top of the ratcheting driver easily adds pressure. Pic 6 shows end result. Screws all tightened up and have considerable strength.
Sarah McUmber-House
Reviewed in the United States on May 3, 2022
I had to totally replace our shower, and wanted to add the safety of strong grab-bars, as aging adds balance and strength issues to the situation. These Moen Peened Grab Bars with concealed screws are just the right thing. The installation instructions are exceptionally clear, and easy to follow. The bars are strong and the mounting brackets are well designed and sturdy. The 'peened' finish on the bars' straight length makes it a much safer grip, so you don't slip when you need to be stabilized.They also look just fine, and the safety reassurance is so much more important than 'designer' style. Plus, they are quite reasonably priced! I definitely recommend them!TIPS:- Mark the line of your studs with 1 1/2" blue painters tape so you can see where they are in your placement area instead of imaging where they might be.- The mounting plates need to center on those studs.- If your shower kit doesn't come with them already attached ($$$!), check with your shower's manufacturer as to where to attach 'backer boards' to reinforce the areas you intend to put your mounts. (I had to do a *lot* of searching to get even remotely clear instructions on this, but finally found it. Added 1x4 and 1x6 pine boards at the specified locations on the back side of my kit. Your mileage may vary.)- Follow Moen's location and installation instructions when placing and anchoring your grab bars! Your safety may depend on these, and you need to trust your work.
Miguel Ángel Juárez Saucedo
Reviewed in Mexico on July 4, 2021
Excelente compra, resistente y el diámetro adecuado
jot
Reviewed in the United States on May 8, 2021
Great product. Looks good, feels good. Did I mention it might also help you stay alive by breaking a fall?My biggest problem was in finding the studs. My stud finder wouldn't go through porcelain and the drywall apparently. So I looked on the other side of the wall, the kitchen. The mounting screws for the cabinets showed quite clearly where the studs were.But here's the bad news. A 2X4 stud is only 1 1/2 inches wide, so it's almost impossible to put all three screws into it. I only got 2 screws on each bracket to hit, and on one I had to angle the 2 screws. For the third screw, I had the choice of a toggle bolt or plastic expander. I went with the expander (because I didn't want to take a trip to the hardware store.) THe bar is rated for 500 pounds, and my wife and I aren't even a third that. So I reasoned that 2 screws in the stud for each bracket would be enough.The bar feels very sturdy, and I'm confident it will do it's job of breaking a fall. I recommend it whole heartedly.
ML
Reviewed in Canada on June 16, 2020
There were already grab bars in the bathroom; however, I needed an additional one. I chose the same company and found the same finish as the other ones... matched perfectly. It's sturdy and keeps me from falling. The main part is textured allowing more grip (even with soapy hands). Worth the investment.I have tiles in the bathroom. I had a professional install it and it was worth it as it requires a special bit to drill into tiles without breaking them.
Recommended Products
