Your cart is empty.
Your cart is empty.MGP Caliper Covers are manufactured in the USA with T-6061 aerospace grade aluminum, TIG welded for strength, powder-coated for durability, and includes a patented stainless steel fastening system. Each set is engineered specifically for the brake caliper to ensure proper fit and finish. No adhesives, tape, or caliper modifications are required. Typical installation time is one hour from start to finish.
Neil J.
Reviewed in the United States on September 20, 2023
Liked the color but when put on the car it was a cheap look altogether and fitment left something to be desired.
N. Oliver
Reviewed in the United States on January 9, 2021
Rear went on easy, the fronts were too small. I reached out to the manufacturer and they initially responded and asked for some information, which I responded with immediately. Two months later I still have not heard a thing. Bottom line the front caliper on a 2007 and later C6 is larger than a 2005-06. there are several variations in packages. Z06 etc. I have some expensive metal covers that don’t fit my car. If MGP is willing to make this right, I will change my review.
Jason Womack
Reviewed in the United States on December 28, 2020
Easy to install and looked great on the car
Jim Beaton
Reviewed in Canada on November 1, 2020
I will give an accurate and fair review when I obtain a full refund for these caliper covers. I will also supply certified documentation to verify my review if necessary!!
Marvin H. Scott
Reviewed in the United States on October 7, 2020
I returned the covers because the front covers did not fit my front calipers. This was even after modifing the clips as instructed by the distributor, MGP. They fit the rear calipers OK but when I was unable to get them to fit properly on the front calipers I removed the rear covers and returned both front and rear for a refund. The covers I installed and attempted to install had some very minor scratches on the inside of the covers due having been installed or attempted to install as they sit against the calipers. Because of this the seller only refunded ½ my money. I contacted them multiple times but they said they were “used” so only refunding ½ my money. I told them they should contact MGP, the distributor, to verify I had a problem with the installation and let MGP refund the rest of the money to them and then to me. They claimed to contact MGP and said MGP had not talked with me, even though I attached an email from MGP with my correspondence to Driver Mods. My last emails to both Driver Mods and MGP have been ovr a week ago and I have not heard back from them. So, at this point it appears I am out $134. At this point I will be posting a negative review on Amazon, Yelp, and the Corvette forum.
peter wood
Reviewed in Canada on August 19, 2019
These shipped very fast about 2 days.But could not believe how cheaply they were made absolute junk, metal so thin and light they felt more like plastic,very hard to install with cheap mounting brackets and tiny nut/bolts .Had too bend all the mounting tabs just to get them to fit on.2 back covers dont fit at all the stock corvette rims hit the cover right away and wore the red paint off the front of the cover.I wish I could get my 300+ dollars back.These where installed on a 2006 c6 corvette.Dont waste your money.
joe
Reviewed in the United States on April 18, 2019
So easy, so good looking! Little pricey, but still ok. Be sure to bend clips from touching rotor or you will get a sqeel. much easier to do first time.
BigJeff
Reviewed in the United States on December 13, 2018
Look great. Easy to install. Not cheap though - proxy for what it is. New rotors were cheaper. 😉
J. Koons
Reviewed in the United States on August 17, 2017
I installed these on a C6 as an alternative to replacing or painting the calipers. Let's face it, the C6 calipers are ugly. These are a great way to cover them up as well as spruce up the look of your Corvette in general. The installation was pretty easy although I did have to tweak the mounts a bit to make the covers fit snugly to my calipers (otherwise they would have rubbed against the wheels). I've had them installed for several months now and have noticed that the wheels don't get covered with break dust like they used to, which is a nice side effect. I would definitely recommend the MGP caliper covers to anyone and have done so when people ask about mine.
Tommy King
Reviewed in the United States on May 4, 2015
Overall a quality product. They are thin, but durable. They have to be thin because there is so little clearance between the caliper and the rim. I like the look and would recommend to anyone wanting a little dash of sport and color behind your rims.
Recommended Products
![Power Stop Front S2632 Pair of High-Temp Red Powder Coated Calipers For Toyota Sequoia 2001-2003, Toyota Tundra 2000-2003 [Model Specific]](images/loading.gif)