Your cart is empty.
Your cart is empty.Product Description
Specification:
Material: Aluminum, Plastic
Color: As Picture Shown
Brushed Controller Size: Approx. 8.3 * 6.5 * 3.7cm/3.2 * 2.5 * 1.4in
Voltage: 24V,36V,48V(Optional)
Under Voltage Protection: 20V,32V,42V(Optional)
Power: 500W
Package Weight: Approx. 600g/21.1oz
Application: Electric bicycles, electric tricycles, electric scooters
Package List:
- 1 * Brushed Controller
- 1 * Throttle Grip
Angelic Loeza
Reviewed in the United States on August 20, 2024
But it doesn't have labels, so be aware...
John Lach
Reviewed in the United States on July 11, 2024
The controller had Chinese markings. No instructions. I could not get the unit to work.
Customer
Reviewed in the United States on May 23, 2024
No power going to motor
jp
Reviewed in Canada on March 23, 2024
Wiring was wrong. Bad instructions. Didn’t work.
Mike Tew
Reviewed in Canada on August 15, 2023
Junk
Bryan
Reviewed in the United States on May 6, 2023
Works. Not happy with a big guy using it. Locks out and you have to hard power cycle the controller. Throttle lead has wires in incorrect position. So it seemed DOA until I swapped the wire to where they needed to be.
Customer
Reviewed in Canada on August 8, 2022
Pas servi
Trent
Reviewed in the United States on May 7, 2022
Wiring diagram does not include English or good enough pictures to determine connections. Handle is not worked correctly so product will not work out of box. After translating diagram on controler and rewiring throttle product does work
Gene Pecoraro
Reviewed in the United States on July 8, 2021
Did not work!! I read the reviews half said it was good half said it did not work
MrJohn613@YouTube
Reviewed in Canada on July 29, 2021
tested it and overvolted with 36v. works good, no problems so far. basic throttle was different than the one pictured , and the labels are vague partially translated but it worked fine after i bridged the plug for on/off switch.
JamiDanielle
Reviewed in the United States on May 26, 2021
The throttle pins were in the wrong place and I had to switch them around. Just match the colors but it's difficult to get those pins out.No wiring instructions but I looked them up and can confirm these are accurate.Wires Interface Description:Yellow & black(1) : brake,Thin yellow (Brake signal)/thin black(Negative Power)Red & Black(2): Brake light,Thin red (power Positive) /thin black (Power negative)Red & Blue(3) : Key Switch(power locks),Thin Red(VCC)/Thin Blue (If there is no power locks,red connection to blue)Red & Black(4) (small cable): Charging port.Thin red (charge input power Positive) /thin black (Power negative)Red & Black(5)(small cable) : indicator light.Thin red (Indicator power output) /thin black (indicator negative)Red, Black & Blue(6): Speed governor(Throttle ) Thin blue(Speed handlebar Signal input) /Thin black (Negtive Power) /thin red(1-4V Positive Power)Yellow & Blue(7) : Motor connections,Thick Yellow (Motor Negative) /Thick Blue (Motor Positive)
PJ 55
Reviewed in the United States on December 18, 2020
There was no wiring diagram in English. Had to Google to figure out how to wire. The hand throttle was not wired to match the controller. Had to move the pins in the plug. Once I figured out it seemed to work ok. I have little faith in the longevity.
Cylo
Reviewed in Canada on October 19, 2020
All in Chinese .. no English manual or instructions...!!!!
Recommended Products