Your cart is empty.
Your cart is empty. Locks Flywheel in Place When Removing Harmonic Balancer on 6.6L Duramax Engines with Allison Automatic Transmissions.
Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement. On 2500 and 3500 pickups, remove metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel. On 4500 and 5500 trucks, remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place. Use 36mm 12 point socket with 3/4" square drive to remove harmonic balancer bolt and re-torque on installation. 36mm 12 point socket can also be used on axle nuts.
Jacob
Reviewed in the United States on January 14, 2025
A must for any duramax water pump replacement
Matt
Reviewed in the United States on August 27, 2024
Perfect tool my Duramax LLY water pump project.
Jordan
Reviewed in Canada on July 25, 2024
Had my water pump off in minutes once I got my bolt out, tools worked great perfect fit
George
Reviewed in the United States on June 29, 2024
If you work on trucks powered by a Duramax Diesel engine then this tool is a must have for your tool box. Makes locking the flex plate super simple for doing various repairs on the engine. This tool allows you to lock the engine in place by inserting the lock into the teeth of the flex plate through the panel under the transmission, then using the 12 point socket to remove the bolt on the crank pulley. Having this tool makes a difficult task much easier.Tip: Leave yourself a reminder note to remove the lock before attempting to start the engine!(I can verify that it fits the LB7, LLY & LBZ engines. I've never used it on anything newer but I've been told it fits all models.)
Derren Siglock
Reviewed in the United States on June 22, 2024
Essential tool set for anyone removing flexplate on duramax. My LBZ wouldn't hold to get enough force to break the bolts loose until this set arrived. Had a chewed up rear engine plate that the one lock did find a solution. Worth the cash,even if used only once. Thanks
Dr. Dan
Reviewed in the United States on February 27, 2024
Used this for my LBZ Duramax so that I could lock the engine in order to remove the harmonic balancer. Due to the heavy torque on the balancer (>300 ft lbs) I had to use a 3/4" breaker bar that was over 5 feet long. This tool held the engine from turning so that I could remove the bolt, and then held it again so that I could torque the new bolt back on when done with the other work.
Jeff Spencer
Reviewed in the United States on December 7, 2024
Had to replace the water pump in my Duramax. This is a necessary tool if you want to do it correctly and efficiently.
CW
Reviewed in the United States on October 4, 2024
This tool was exactly the tool I needed.All of the components for my LB7 worked as advertised.You will need a way to drive the socket. It is a 3/4" drive.For me (LB7) the flywheel clamp worked just fine. The trick seems to be in removing that flywheel clamp when you're done. For me this required two people. One to wiggle the crank, the other to keep a little pressure on the clamp such that it would come out once the pressure is removed.Don't forget to put your flywheel inspection cover plate back on!
Customer
Reviewed in Canada on June 20, 2023
It works, quality is ok. For the price it's good
Jamie Springs
Reviewed in the United States on June 17, 2022
I wasn't sure because it was so cheap, but I needed this part and had already spent enough on the water pump. Way easier and faster than the engine crank method. The flywheel lock tool and socket did not break and got the horrible job done. It made it a little easier without risking any damage. I highly recommend this if you are changing your own water pump on a duramax. This was perfect for my LBZ.
Robert Ramchuk
Reviewed in Canada on February 9, 2022
This worked well for me. Was easy to un bolt the balancer.
Wendy
Reviewed in Canada on December 5, 2022
Worked easily and flawlessly.
Nathan Graff
Reviewed in Canada on October 6, 2021
I thought I"d have to spend a lot more time getting the front crank bolt out so I could change the water pump. This and a 48" breaker bar on an 01 made short and quick work of the job.
Recommended Products
$35.19
$ 16 .99 $16.99