Your cart is empty.
Your cart is empty.Product Description
Bar end turn signals
White Color light for Day Time Running Riding Light ,Amber Color Light for Turn Signal.
12 LED Turn Signal Lamp Scooter Blinker Flasher Resistor Front Rear Light Assembly,for Chopper Cruiser Classic Vintage Motorbike.
- Bright
- 360 degrees visible
- Amber color for turn signal
- 3-Wire Design
- Handlebar end light
- Turn signal
Customer
Reviewed in the United States on February 16, 2025
Product is garbage now Iv used them many times before and they worked great. Bright white light bright orange turn ligh. Last two sets I ordered where junk one set wouldn’t work. White light bright orange fine but wouldn’t blink. If you disconnected white light orange would blink. They sent new ones I haven’t return the junk that cost me as much in gas to go to post office as they cost. The second both worked proper but one of them the turn singly light wasn’t bright. After testing them twice one stopped working on the turn signal like the first batch ordered and the second one the turn signal light looked like only 1/5 of the leds are working. What use to be a good product is now junk.
Louis Judge
Reviewed in the United States on February 15, 2024
The media could not be loaded.
Dj Vicman
Reviewed in Canada on December 6, 2024
Replaced old broken ones on my scooter and these work better than stock I figure even if your just adding to your ride their perfect addition for safety
Tom N.
Reviewed in the United States on June 10, 2023
I bought 2 sets of these to install on my friends motorcycle in Mexico. I live part time in an area full of American and Canadian retireees in Mexico who are blind and oblivious to motorcyles riders. The more additional lights that can be seen, the better !!!I put one pair up near the end of handle bars so they could easily be see by oncoming and side traffic. I put the other pair near or under the seat and sides of the motorcycle so it could also be seen from side traffic and well as rear traffic.
Justin
Reviewed in Canada on April 13, 2023
Install was fairly straightforward as with all light wiring. The wires provided are small which makes the wiring a bit more tedious. But my big complaint is they only lasted one 5min ride before the lens fell off on the road never to be found again. So after all that work of putting them in and drilling wiring holes in my bars they need to be taken off. Will contact the seller to see if they rectify this with a new set that I will super glue the lenses on for peace of mind
Frank Gemeiner
Reviewed in Canada on August 7, 2022
I drilled a hole through the screw on bar end cap . Mounted the light to the screw on end cap . Connected the wires and reinstalled the end caps . Love the look ..
Robb Ryniak
Reviewed in the United States on March 20, 2022
The media could not be loaded.
Torque
Reviewed in Canada on October 30, 2022
Not bright enough for daytime Very well-made beautiful aesthetic but not bright enough for day time
Grant
Reviewed in Canada on July 18, 2020
Works great...however I ordered yellow and it was checked yellow 9n the box but the light was only white...no yellow what so ever.
Eady
Reviewed in the United States on February 21, 2019
I love these! They improve your visibility at a 360, are bright and functional which looks cool plus gives you more safety while riding at night, it’s a great product. Requires some elbow grease but when you’re done installing, it’ll be worth every penny and effort. Now, to install:You’ll need to connect black wire to turn signal ground, red wire to hot (blinker) corresponding signal side and white wire to key switch power (tap the white wire into any running light wire that turns on when you switch on the ignition) you’ll also need either an led relay flasher or a pair of resistors for this setup to properly function. Though, careful with the resistors, functional but get quite warm. Place them far from other wires or plastics, if possible mount them on metal.I’m currently using these on a Honda Ruckus / Metruck.
Customer
Reviewed in the United States on September 27, 2018
Hey guys,Great product, cool looking lights. They run bright white and flash amber for turns.Really loved these lights but the one of the glass end caps, which magnifies and directs the light, came undone while riding and I lost it on the road :( :( :(So the light can only be seen when looking directly at it from the side, not from in front or behind.I'd hope I could get a replacement!!
Willy L.
Reviewed in the United States on June 16, 2018
Those are the best cheap option for this model of turn lights. I had some cheap one made of plastic (ebay) and it was a shame, the bold itself was made of plastic and it broke while adjusting it. BUT THOSE! All metal! and the light is bright and clear! As written by other reviewer, the white light is brighter then yellow but hey...it works! I use them near the headlight, I'm too scared to put them on the handlebar: that's the first thing that hit the ground in case of accident.PROS:- METAL! not plastic.- Cables are long- Bright white lightCONS- The cables are really weaks, you can barely sold them without metling- I wish the yellow was as bright as the white
DEW
Reviewed in the United States on October 29, 2018
These lights work great mounted vertically on an ATV or UTV for turn signals. The lights are very bright and since they are visible for 360 degrees the placement is not critical. The lights can be seen by other vehicles as well as the operator. You can drill a hole the size of the threaded tube and install them with the rubber bushing on the back side. When the nut is tightened, it presses the rubber bushing against the flat surface and they are very secure. They can be mounted on the top of the fenders or or near the driver to provide additional visibility as shown in the photo. The only special requirement is the need for about 2 inches of clearance below the light. The wire for the white light is not connected in this instillation.
Recommended Products
$16.99
$ 6 .99 $6.99