Your cart is empty.
Your cart is empty.Product Description
Add Some Fun To Your Life!
INKJET Waterslide Decal Paper Operation Steps:
Step 1: Print Image
Create and print your design with an inkjet printer. Let it dry for a while.
Step 2: Spray Acrylic Coating
Seal the print image with the clear acrylic spray. Spray 3 even coatings over the image allowing each coating to dry then spray again. Wait for it to dry completely.
Tips: The ink will dissolve in water if the coating is not sprayed evenly.
Step 3: Cut Out Image
Use scissors to cut out the image. Leave a border of 3 mm around the design for best results.
Step 4: Soak In Water
Soak the deal in room temperature water for about 30~60 seconds or until the paper backing can slide easily. Take out the decal from the water.
Step 5: Slide
Place the decal onto the desired surface with the image side facing up. Gently hold the edge of the decal while sliding off the backing sheet.
Tips: Put some water on the surface for easier sliding.
Step 6: Smooth and Dry
Use a paper towel or mini squeegee to remove air bubbles and excess water out from behind the decal.
Then let it sit to dry by nature.
Tips: Ceramics can be baked in an oven at 230℉ for 10-15 minutes for more strong adhesion.
Extra coat of epoxy resin can be used on the finished decal for more protection.
Ayla McGhee
Reviewed in the United States on March 4, 2025
I bought this because I didn't have enough to get the decals I usually purchase. And for lesser sheets and cheeper price, it actually gets the job done.
J. Chicos
Reviewed in the United States on February 7, 2025
Purchased these decal sheets once prior without problems. This time they were rolled inside the shipping envelope!! It took over a week for them to lay flat again
Customer
Reviewed in the United States on February 25, 2025
Not great - did not stick well
Mike
Reviewed in Mexico on August 17, 2024
Buen producto.
Jodie Pender
Reviewed in Canada on March 20, 2024
This was my first time using waterslide decals and I found the process easy and quite fun.
Ron
Reviewed in Canada on February 24, 2024
Too bad it doesn’t have a clear background… needs a program that works without color background. Gotta be as light as possible of the same background. And in order to use you MUST put a clear spray on it or it’ll dissolve
Miss Grinch
Reviewed in the United States on February 16, 2024
directions say they want you to top coat them before you place them. the problem with that is once you spray them you’re eliminating the residue that allows you to stick it on the object in the first place. This led me to wasting a lot of sheets and not happy with the results. when I try to place the sticker without using a topcoat on it, the image was dissolved from the water. how can this be a water transfer if water is making it ruin the image. this happened on both my inkjet and my laser printer so if it’s ruining an image that was printed with a laser yeah no thanks
Jack
Reviewed in the United States on November 15, 2024
If you follow the directions that are on the package, you’ll have decals even better than those commercially available. A few hints: set your printer to the high quality paper setting; after printing let the ink dry; then spray on a clear acrylic or lacquer making sure there’s at least three coats. When that dries you can apply the decals to whatever. With the right products you can do it all in an evening. The results I got were great. It was easy and the decals didn’t tear when applied. The writing and logo decals are on HO scale scratchbuilt buildings.
Brenda
Reviewed in Mexico on November 14, 2024
Lo volveré a comprar muy pronto, es muy fácil de usar y no se derriten con el agua. Durables
elle
Reviewed in the United States on January 8, 2024
Easy to use, after spraying with clear coat and placing them on my tumblers it slides on easily. Colors come out vibrantly. I've bought these many times , tried using other but they were not as good.
Glenn Matthiesen
Reviewed in Canada on January 19, 2024
I found this waterslide decal film easy to work with and provided excellent results. As you can see, I am using this product for scale modelling decals. The decal prints well, takes less than 30 seconds to release in warm water and sets exceptionally well. I had to peel off one of these little decals and was impressed with the adhesion and flexibility of the film which allows it to conform perfectly on irregular surfaces.In a separate article, I read that Rustoleum 2X Semi-Gloss Clear was rated the best for sealing the printed ink on the film. I applied three light coats as recommended which provided excellent results. I waited 5 minutes between coats, then 30 minutes after the third coat. Then I carefully cut out the decal, immersed in warm water for about 20 seconds and applied. You want to align the decal as close as possible as you don't have much time to realign before the decal starts to adhere. Highly recommended!
Tiffany Hall
Reviewed in the United States on April 9, 2024
Works great, excellent print quality...I just wish the transfers wouldn't tear as easily.
BL
Reviewed in the United States on April 4, 2024
I used on my tumbler. Easier to use
Recommended Products