Your cart is empty.
Your cart is empty.Caleb
Reviewed in the United States on February 3, 2025
The media could not be loaded.
Rene D
Reviewed in Canada on January 19, 2025
Great quality as always.. Adds weight right where you want it! Looks great as well 👌
GAMEBRED
Reviewed in the United States on September 29, 2024
Fits like a gloves on my trx4m defender. Highly recommended.
Alex T. Richards
Reviewed in the United States on May 29, 2024
This is a great fitting product. I happened to lose a couple of the spacers. I e-mailed the company to buy replacements and they offered to send me replacements for free. This was rather unexpected and very helpful.If you buy these i would recommend going to the company website, they have more detailed photos that will help with installation.
Curt Williams
Reviewed in the United States on January 6, 2024
Ok, so I think most folks aren't understanding how the bushings between the C-hub and the knuckle are actually supposed to work based on the reviews I'm reading. There is a bit of a tight tolerance issue, and its worse if you get the gray or black ones due to the surface coating.The bushings install from the INSIDE of the C-hub out - the large flange is a contact surface and should be to the inside. ****If the bushings DO NOT FIT by dropping into place with gravity, then it is too tight. You need a 7/64" drill bit. At low rpm, ream the holes out a little at a time until the bushings drop in and spin freely. This is important because the bushings are supposed to rotate freely. The small end of the bushing supports the screw head and makes a bearing surface that will rpotate with the knuckle. Doing it this way, you will need NO LOCTITE. The material is brass and is soft. Brass threads shape and deform under pressure locking the screw into place if you tighten it down. You should be able to fully tighten the screw without ANY BINDING, because the bushing can now rotate AS INTENDED. Go slow with reaming out the holes. Less is more. Do a little, check fitment. Rinse, wash, repeat until the bushing spins freely and will drop out of place with just gravity. It took me 15 minutes to fix mine. Zero binding.
K Walker
Reviewed in the United States on September 28, 2023
Have to sand these a bit to fit in the injora metal extended axles. The reason for 4 stars is because the fit wasn’t great. They work well and are much heavier once properly fitted.
Trudi
Reviewed in Germany on September 22, 2023
Einwandfreie Qualität, Verarbeitung und Passgenauigkeit.Klare Empfehlung für Leute, die ihren Crawler eine andere Optikund einen geänderten Schwerpunkt verpassen wollen.
Jose A.
Reviewed in the United States on July 16, 2023
I had to fix the issues by filling the hubs to have better steering from binding up it wouldn't go straight while driving forward and it's more play on one side than the other inside where the big bearing goes, so I had to use 2 sets of shims washers on each side. New update 11/12/23 after all I'm happy with the brass c.hubs & brass steering blocks, it runs perfect i end up taking off the shims between the hexs & outer bearings. I figured that lil play is normal in the front wheels due to testing with other TRX4M's i own. Definitely will buy another set off brass for my other TRX4M's i have now for the Chevy K10, Ford F-150 H.T. thank you INJORA
CaWa
Reviewed in Germany on June 16, 2023
Injora typisch sehr gut verarbeitet, die Kugellager von Injora passen 1a, das Gewicht ist dem 1/18er angemessen gewählt.Ein sehr gutes Upgrade um das Gewicht nach unten zu verlagern.
DILLIGAF
Reviewed in the United States on June 1, 2023
Quality pieces that also add a nice bit of weight…. The kit has spacers for the C blocks that need to be installed on the inside so the steering knuckles are perfectly spaced
Dale and Kirsten
Reviewed in Canada on December 23, 2023
great love the look of the black and brass
Bruno Gobeil
Reviewed in Canada on November 12, 2023
Installation facile et belle amélioration des performances.
DAKOTA BRAY
Reviewed in the United States on October 1, 2023
Collar system does not work as it should for the C to the wheel hub. As you use the car they loosen causing you to potentially lose a needed specific collar. Thankfully they come with a spare as I already had to use it. Now I have to keep an Allen in my pocket and check very frequently. Normally Injora stuff is a great value and function.
Recommended Products
