Your cart is empty.
Your cart is empty.Product Description
Aopkeo, a new choice.
HPA Regulator for Paintball Airsoft PCP
Max 4500psi input and 800psi, 1800psi, 2200psi output.
Input thread is M18*1.5 or 5/8"-18UNF, output thread is G1/2-14.
6000psi Gauge
1 inch 6000psi pressure gauge, with 1/8NPT thread.
7500psi Disk
7500psi input burst disk.
Fill Nipple
Standard 8mm male quick discoonect fill nipple, with one way foster.
Output Pressure Disk
Output pressure burst disk, depending on the output pressure, it may be 1800psi or 3000psi.
Double O-rings
Output thread with double polyurethane o-ring, has a service life 10 times that of urethane material and can be used under a pressure of 6000psi.
- High pressure resistance
- Low temperature resistance
- Good friction resistance
- Easy installation
Pressure Gauge and Filll Nipple On The Same Axis
6000psi pressure and 8mm male quick disconnect fill nipple in the same axis, more convenient to use.
Input burst disk and output burst disk are located on both sides of the axis.
All pictures are real photos without any beautification. We hope to present you with the most authentic product.
- Pressure gauge and filll nipple on the same axis
- Two burst disk are located on both sides of the axis.
- Real photos without any beautification.
Belleville Spring Stack Orientation
Belleville spring stack to reduce air pressure, there are different orientation for different output pressure.
Each regulator is debugged before leaving the factory to ensure accurate output pressure.
Six Specifications
This regulator with six specifications, the different input thread and output pressure. You can choose the one you need.
All the regulators with the max input pressure 4500psi.
M18*15 Output 800psi
M18*15 Output 1800psi
M18*15 Output 2200psi
5/8"-18UNF Output 800psi
5/8"-18UNF Output 1800psi
5/8"-18UNF Output 2200psi
Product Size and Weight
The size is 1.1 inches*3.2 inches(8.2cm*2.8cm), weight is 7oz.
Gauge size is 1inch(2.4cm), thread is 1/8NPT.
JOVEN
Reviewed in the United States on September 26, 2024
Love the Price. Great quality feels solid. Craftsmanship is there. Unfortunately it din not fit my Air Tank. I'm not sure this was the right 5/8 18UNF. Loved the Double Orings on the Regulator.
bryan
Reviewed in the United States on September 15, 2024
this reg bust the 3 k safety so I installed a 5 k from my old tank and that burst too not sure what's going on
Bazooka Joe
Reviewed in the United States on September 13, 2024
Purchased to upgrade the 1100psi regulator on my Sig Virtus PCP. Once I calculated cost of shims and washers I found it would be cheaper to just buy this complete regulator. It works as it should with no leaks.
Tim Chambers
Reviewed in the United States on June 2, 2024
Now I am able to fill my paintball tanks. Thank you.
kbye55
Reviewed in the United States on June 1, 2024
Odd that all fittings leaked air pressure an I was able to use Teflon Tape to seal the leaks temporarily.
Jay R.
Reviewed in the United States on May 29, 2024
Simple old school looking HPA regulator. Piston style like they have been making for years that looks like maybe they copied an early ninja style reg down to the double O-rings. The bonnet can be clocked by loosening the set screw and turning the bonnet. Just make sure you tighten the set screw down again. Over all happy with it so far, it fills properly, is holding consistent pressure and doesn't leak.
john
Reviewed in the United States on May 16, 2024
Happy
Juan
Reviewed in the United States on October 16, 2024
Wanted to upgrade the reg on the gauntlet 25 with the 2200 regulator fits perfectly and upgrades the foot pounds(50-57)and fps
Recommended Products