Your cart is empty.
Your cart is empty.
Main Features:
It can be used for end turn bundling and connection insulation in small motors. It is also used for cross-over insulation and out wraps on bobbin wound and form wound coils for large rotating machines to bundle conductors and reinforce insulation and it can also be used as wave solder masking of printed circuit boards.
Features includes good adhesion, good tensile strength, low temperature application, short term, high temperature resistance, clean removal, good chemical and solvent resistance, UV resistant, easy unwind, good abrasion and moisture resistance, waterproof backing.
Widely Used:
MULTI-PURPOSE APPLICATIONS - AIYUNNI adhesive tape is ideal Extensive for a variety of home and commercial projects,such as installing LED strips, 3D printer bed ,Computer, cell phones, Electronic Repair, Automotive,Solar industries, circuit boards and (PCB) components ,Fiber Optics Cable,Home electronics, large appliances, industrial machinery, transformer, motor, coil, capacitor,frequency conversion power,and More ( list not all inclusive).
Specifications:
One-side self-adhesive design.
Substrate material: Polyimide polymers film and Dow Corning silicone.
Withstand voltage: >6000V
Heat resistance: The highest temperature up to 572 ℉ (about 300℃), Long-term temperature: 500 ℉( about 260℃), Short-term temperature: 572 ℉ ( about 300℃)
Size: Length 108ft x Width 50mm x Thickness 0.05mm
100% brand new and high quality High Temperature Heat Resistant Polyimide Film Adhesive Tape.
Package includes:
1 * 2 inch X 108ft High temperature resistant tape Polyimide Film Adhesive Tapes
FP
Reviewed in the United States on December 15, 2024
This knockoff "Kapton Tape" is dirt-cheap and it performs exactly the same as the much pricier brand-name tape. I use it on a 3D printer's glass bed. PETG plastic sticks to glass too well. Putting this tape on the glass keeps that from happening. When switching back to PLA, the tape is easily removed, and is much less messy than using glue-stick as a barrier. One roll of tape lasts a very long time.
NP
Reviewed in the United States on February 13, 2023
I bought magnetic flex plates from Wham Bam with their PEX hi temp plastic but I had very little success with adhesion with plain old PLA. So I bought this Kapton tape and replaced their PEX film with this material. It works well.Applying this film takes practice but I can do it successfully every time now. Pull back about 1" of the roll and tape that edge to the edge of a clean counter so the tape roll hangs down. Next, pull down and unroll a length longer than your build surface. Clean your build plate with IPA and the spray it heavily with soapy water or something soapy like Windex. Now cut the roll free of the hanging tape, peel the edge off the counter, position the tape on the build plate and squeegee the water out for perfect results. Sop up the excess water with a cloth. If you need to trim the tape, find a flat clean surface you can cut on, flip over the taped build surface and used a very sharp exacto knife or new razer blade while pressing on the edge your cutting. If you attempt to use it right away, you'll get bubbles. Leave it for a few hours or place it on your heated platform at 40 degrees C for 20 minutes.I always scrub the taped surface with 000 steel wool and clean with IPA after scrubbing and between prints. You will need to re-scrub once in a while for good adhesion. The optimal bed temperature for PLA is 60 degrees C.
Joey
Reviewed in the United States on April 23, 2020
I love this stuff! I have been using blue tape for years and the first time that i put this on the build plate, my printing got elevated to the next level. It produces a glass like finish on the build plate side and is super easy to get off when the print is done. It also lasts for ever as long as you don't nick or scratch it when removing the print. It is a bit of a pain to put on the build plate but the benefits far exceed this little issue.
Customer
Reviewed in the United States on May 23, 2019
Used this for a soldering project. It does ignite when using a torch (duh), but she still holds well enough and worked just right for the project I had. I would definitely purchase it again.
T. Snider
Reviewed in the United States on December 2, 2019
I bought this to coat the glass print bed for my MakerGear M2 printer because the width of the tape (200 mm) is perfect for the glass. The only reason for deducting one star is that it can be very tricky to work with but I can't blame the product so much as the nature of the product. It took a few tries to get the method down (I'd strongly recommend watching a YouTube video) and it took 2 people to get it right for me. The most difficult thing about working with it is if it tears then it is very difficult to be able to get it back without the tear. My advice is if you have that happen, the best method I found to remedy it is to simply tear the tape all the way to the edge and remove that piece. Trying to pull the tape back beyond the tear is nearly impossible. Other than that, it works great and does a good job protecting the bed and providing adhesion.
R. Lindgren
Reviewed in the United States on December 14, 2019
Resists heat well. Sticks to what you want t to stick to, but it is easy to unroll or remove, and cuts easily to shape. I used this in a Li-ion battery project that gets hot when pulling deep amp draws, and there have been no issues with the tape deforming or peeling. Great price as well!
Real Man
Reviewed in the United States on November 7, 2019
I have a 3D printer with a 150x150mm print bed, and this is working great. Good price and stable and reliable film. Would buy this again, no question!
K367
Reviewed in the United States on April 10, 2019
The media could not be loaded.
Recommended Products
