Your cart is empty.
Your cart is empty.Product Description
Hantek AC/DC Current Clamp Meter for Oscilloscope CC-65 20KHz Bandwidth 1mV/10mA 65A with BNC Type Connector
AC/DC Current Clamp CC-65:
AC/DC Current Clamp, 20kHz Bandwidth, 1mV/10mA, 65A; It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms. Supplied with coil cable with BNC plug.
Application:
- Power circuit measurement and malfunction analysis;
- Motor drive of frequency converter (or other electronics) measurement;
- Power electronics equipments measurement.
Features:
1. It is a transducer which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms.;
2. Its current transducer is composed by permalloy and hall element, which linearly transform the AC or DC current to AC or DC current voltage;
3. And if connect to an oscilloscope by BNC type connector, you are able to observe the current waveforms; If connect to a multimeter by banana type connector, you can obtain the current data.
Specification:
DCA Range:
1 mV /10mA +/-(1.5%+/-5mA) 10mA ~ 20A
1mV/100mA+/-(2%+/-20mA) 100mA ~ 40A
+/-(4%+/-0.3A) 40A ~ 65A
Operating Temperature: 0Cto 50C 70% R.H.
Storage Temperature: -20C to +70C, 80% R.H.
Battery Type: 9V DC, NEDA 1604, 6F22,0006P
ACA Range:
1mV/10mA:+/-(2%+/-30mA) 100mA ~ 10A (40Hz ~ 2KHz)
+/-(4%+/-30mA) 100mA ~ 10A (2KHz ~ 10KHz)
+/-(6%+/-30mA) 100mA ~ 10A (10KHz ~ 20KHz)
+/-(8%+/-30mA) 10A ~ 15A (40Hz ~ 20KHz)
1mV/100mA
+/-(2%+/-30mA) 200mA ~ 40A (40Hz ~ 1KHz)
+/-(4%+/-30mA) 200mA ~ 40A (1KHz ~ 2KHz)
+/-(6%+/-30mA) 200mA ~ 40A (3KHz ~ 5KHz)
+/-(8%+/-0.3A) 40A ~ 65A (40Hz ~ 20KHz)
AC/DC Current Clamp
Captured Conductor Size: 9mm maximum;
AC/DC frequency range: Up to 20 kHz;
Effective Measurement Range: 20mA to 65A DC.
CC650:
AC/DC frequency range: Up to 400Hz.
Effective Measurement Range: 20mA to 650A DC.
Waveform Display
Show you the specturm frequency interface in detail for you to observe the operation.
Package included
1 * Current Clamp with BNC Plug
1 * User Manual (English)
Kindle Customer
Reviewed in Australia on February 6, 2025
Very happy with this product and it works perfectly.
Daniel
Reviewed in the United States on January 27, 2025
Buena
Roadshowe
Reviewed in the United States on January 25, 2025
The unit worked well enough for the first 2 years.It stopped working and I threw it into the "bin".I purchase a different amp clamp that had a better build quality.Last night I decided to make a final determination. Open it up one more time. If I could'ntget it to work it was going to its final resting home.I noticed if the on/off switch was pressed in firmly and held the power light would flash.Maybe there was hope?Opening the unit to get at the internals is something of a rubic cube.There are two metal "paws" retained by the on/off switch against the circuit board.Apparently there were not "springy" enough to make consistent contact with the pads on the circuit board.I re-tensioned the paws, put some Sanchem "A Special" grease on the pads and re-assembled.The clamp came back to life!The zero button still sticks, just have to "jiggle it".Seems like simple "quality issues" for Hantek to remedy with a couple of ECs.
Jesus
Reviewed in the United States on August 5, 2024
It works very good for low Frequency currents
Jawaharbabu
Reviewed in India on August 17, 2024
Super
Dutchstone G.
Reviewed in the United States on March 15, 2024
Nice product for the money. Works well on my oscilloscope..
Julian Bolivar
Reviewed in the United States on March 14, 2024
I used other expensive options on the market and this probe is really good, and it is very precise and lest noisy that other expensive ones.The only thing is it should include a better and more detailed documentation and/or manual.
Customer
Reviewed in Canada on February 3, 2024
Used for electronic testing
Dante
Reviewed in Mexico on April 20, 2024
Exelente muy buena opción , la utilizo para el osciloscopio de autel y para el osciloscopio hantek
Troy H
Reviewed in the United States on January 22, 2023
Tracks great with my $1000 Tek clamp on with a similar range for what I use it for. After trying it for 5 minutes on a project I already set up, I am buying the larger current, slower model for car starter motors and the like. Would have been great if I knew the higher gain setting was only for 2 amps and below, but it works just fine at the lower mV/mA setting.
Michael
Reviewed in the United Kingdom on March 25, 2021
When I first got my new current probe out of the box, I thought it was dead. Plugged the 9v battery (Not Included) into the back, plugged it into my DSO, switched it on, and... nothing. No lights. No change in the level when I hit 'zero', no readings when I clamped it onto the Vin line on my project.Except sometimes when I wiggled the switch just the right way, pressed down on it, the green 'Power' light would flicker for a second. I gave it a little shake, and I could hear a little rattle.I took the hazardous step of opening the back to see what was going on, and the problem was immediately apparent. Instead of using a discrete 3-position dptt switch, there's a hacky little arrangement that's prone to failure if you look at it funny. The plastic switch wiper has a pair of ductile little pieces of bent copper which are retained solely by compression between the wiper and the PCB underneath, and as they slide back and forth they make or break connections between tinned pads on the PCB. I suspect that pressing down too hard on the switch can bend them out of shape and let them fall out of place.It was a fiddly little fix bending them back into shape and lining everything up so it didn't fall apart again when I closed it back up, but it seems to work well enough as a current probe now. Sensitivity is acceptable at 100mv/A. I haven't had time to formally assess the accuracy and frequency response, but it seems to work reasonably at the low frequencies and currents I was using today.
Gene Selkov
Reviewed in the United States on September 1, 2020
I have only made one experiment, but I am happy with the result.Captured on the scope is a single TIG weld pulse. The current was set to 40A; The probe registered about 37A. I don't know how well the source is calibrated, so can't blame either the probe or the source for the inaccuracy, but the result is pretty good for what I want to do -- I need it to calibrate the spot timer and to understand the waveforms in different weld modes.The bandwidth is more than good enough for that. The time scale shown is 2ms/div; the claimed bandwidth of more than 20kHz looks credible. I actually saw a very well-defined trace of ignition current; it looked like a decaying sine wave with a frequency far above 20kHz. Part of it is seen as the bright blob at the start of the pulse; the front was not captured with this trigger setting and the tail of the ignition waveform washed out in the flood beam while I reached for the camera. I was not too concerned with ignition, so I didn't bother capturing it, but I know I can at least see the first harmonic and pulse enevelope of ignition current, should I ever need to observe it.
Mike
Reviewed in the United States on October 9, 2016
This is a must have accessory to have with ANY DSO! I have used it with my bench scope and I have used it with my little open source pocket scope (needed a $5 adapter). Being able to see current flow is hugely helpful in troubleshooting electrical issues esp in automotive applications. Injectors, ignition coils, pumps and motors, you can see how much power any of them are drawing right from the fuse box with a tool like this.For example Imagine being able to see if your power window motor was bad with out taking your door apart. With the right know how you can with this tool. Saves time, saves money and makes things easier.Like all tools you need to know learn how to use it, to unlock its full diagnostic potential, but the actual function of the tool is simple turn it on, clamp it over a conductor, and get a reading. Simple.The only compliant I have is I think that the lead can seem a little short at times but that is easily remidied by using a BNC extension cable.So bottom line if you spent the money on a scope you should buy one of these.
Recommended Products