Your cart is empty.
Your cart is empty.Product Description
Application
- For many Cars. Fits M20 threaded Oil Filter. (many Ford Probe , Mitsubishi , Subaru , Honda have these threads)
Description
- Center Adapter: M20 x 1.5 & 3/4 x 16 UNF Thread; Supports Oil Filters That Has M20 Thread & M20 Block Fitting
Benefits
- Simple bolt on replaces side cover on oil pump base
- Advantage is it doesnt make the oil filter sit even lower
- Allows fitment of an oil cooler without the use of a sandwich plate adaptor
- It Mounts between the Block and oil Filter, provides in and out ports, with connectors that fit AN10 fitting
Package Includes
- 1X set, as shown in the picture
Customer
Reviewed in the United States on November 24, 2023
The ported holes do not line up inside restricting flow. Would be 5 stars but looking through the port its about 50% covered by the ports not matching up.
Mark Jeffes
Reviewed in the United States on April 29, 2023
Total waste of money. Poor Machining metal flakes still in the Machining (see pictures). One fitting wouldn't even screw all the way in. When I tried to return it I had to pay for shipping. Manufacturer gave me 80% of what I paid back and told me just to keep it so they know it's crap. Don't buy.
Kenneth
Reviewed in the United States on June 30, 2022
I'll start by saying it looks good. The threads are cut well, the machining and coating look decent, and the fit is good. That is however where the good part ends. Despite everything fitting properly and all the product is simply incomplete. I found way too many loose metal bits inside clinging to the ends of the threads to be okay with installing this right out of the box. It needs some Dremel work bad, like really bad. That would fix everything wrong with it. I strongly caution anyone buying cheap car parts to inspect them before installing. Then again it's 30$ and man hours are expensive. Still there really needs to be a warning on the product page stating that the part may not arrive in a finished state if this is the corner they are going to cut.
Mike Thomas
Reviewed in the United States on August 30, 2021
These are well-made. Heavy duty and thick, quality material. FedEX once again lost my package, which is not the seller's fault. The seller replied to my messages right away and followed up each time. GREAT CUSTOMER SERVICE! They sent me a replacement at no charge. Thank you very much!!! I am very happy with the product. If anyone has a leak, they did not install this properly. Use the appropriate thread sealant and quality hoses. I have been working on engines for 35 years and these units are great.
Josh S
Reviewed in the United States on November 4, 2021
The 2 piece brass adapter seems to have been threaded on an angle. The other adapter which I cannot use seems fine.Edit, The seller sent a new one right away that was free from defects.
Customer
Reviewed in the United States on March 14, 2020
Looks nice but both sensor holes had bad threading half way in. I had to use a tap to fix it. Secondly if you have a temp sensor that has to go in past the threads you can't use it. The threads go in just below the where they stopped machining out the inside. I used a carbide bit to finish machining out the area myself. So my temp sensor would fit.
Taildrager1949
Reviewed in the United States on December 12, 2019
This relocation kit looks great it really makes it east to add oil cooler to the system and the fact that it has double o rings to seal against engine block is nice and not a crappie catsting like other companies are putting out is a plus the fittings ane nice .If you are using oil pressure triger switches for fuel pumps or electric fan there are 2 porst in it or a place to hook guages .If your not using the extra ports make sure you seal them unlike so of the reviews that bitch about them leaking when they put on a part out of the box .Who does that take a part you get in the mail go out to your garage and screw it on your car without cleaning it and checking it over before installing it? Then writing a bad review because someone in a factory on the other side of the world didn't tighten the plugs in the adapter, that isn't their job , their job is to make sure all the parts of the kit are in the box .When I'm done with this review i'm ordering a few more of these because they are a great looking functional part.
Torsettow
Reviewed in the United States on July 27, 2018
Great product I’ll start with the bad The only problem I have found with this adapter kit is; The two small auxiliary ports for pressure Grage, etc. If not used they are difficult to seal with the bolts included in the kit! I debated whether or not this should subtract a star however having given thought to the price of the product I couldn’t complain The only other negative is based on the car that I chose to install it’s a 2009 Honda Civic SI I could not find any reference to whether this product would work or not I had to get down to the nitty-gritty of checking sizes and measurements ultimately yes it will fit if you remove or bend the heat shield for the oil filter Other than that this product is great it bolted up nicely snuggly make sure you use the proper adapters for the size of the oil inlet I noticed that the two different sizes were close enough that you could mistakenly put the smaller male adapter into the female and it will tighten but this will ultimately shear off
Recommended Products
$199.38
$ 84 .99 $84.99