Your cart is empty.
Your cart is empty.Product Description
Susan Maninfior
Reviewed in the United States on February 2, 2025
I put this on with a foam brush over quarter sawn white oak. I first put 3 coats of Danish oil on and let that cure about a week and then lightly sanded it with 400 grit sandpaper before putting the Arm R Seal on. Several people commented on streaks using the satin finish but I did not experience that. I did pay close attention to make sure that the application was as consistent as possible and not excessive. The finish dried out nicely.
William Perschau
Reviewed in the United States on January 22, 2025
Easy to apply, great protection, just follow the directions and you’ll get a great result!
hans kouwenhoven
Reviewed in Canada on January 20, 2025
A little pricey but very good!
Jeremy
Reviewed in the United States on September 2, 2024
Truly makes for a protective barrier, I put it on my kitchen table. Nice shine to it too.Unfortunately, shipping was pretty slow, hence 4 stars.
Janet Quarles
Reviewed in the United States on August 12, 2024
After trying MANY other options, I find this the easiest to apply. On smaller pieces - use a blue shop towel to apply. In larger pieces, a sponge brush works perfectly! Gorgeous finish. If you don’t like the warm hue it adds, I’ve mixed some of the gel stain I used on the piece in with some top coat (about 20% gel stain to top coat) in a little dish and it Muted that golden hue.
CLE TOWN
Reviewed in the United States on December 24, 2024
I have been using this product for a while now and I like the results. I recommend it.
Vaughn Jensen
Reviewed in the United States on November 18, 2024
Such an easy product to work with, and the final project turned out great!
S Jacques
Reviewed in Canada on April 7, 2024
Very satisfied with the product
Liam H
Reviewed in Canada on June 17, 2023
This satin oil based sealer goes on smoothly and dries to a smooth silky finish. I generally put on 4-5 coats. It is easy to apply with a small towel the wipe off the excess with a separate towel. Then let it dry for at least 24 hours.I learned most things by going to you tube. There is a wealth of information waiting for you.
Bklyn Babe
Reviewed in the United States on November 11, 2022
We tested almost a dozen products to use for finishing all the interior woodwork on the first floor of our home. This product was the best. It was easy to apply with a cloth applicator, dried well and looks great.The Arm-r-seal satin finish must be stirred every time you dip your applicator into the can In order to achieve a satin finish, but that is typical of any finish that is not high gloss. It should not be brushed back and forth a lot but it levels itself very well as it is thin. It dried enough to handle carefully in an hour but you must wait about 24 hours to recoat Buffing with a 3M pad between coats is recommended.Please note it has a strong odor though less so than oil based polyurethane. You will need a respirator if you are working with it indoors, or at least, work outside. This is a urethane varnish, very similar to spar varnish, but without the UV protective ingredient in spar varnish. It is softer than polyurethane so it would not wear as well on a floor or a bar top. For our project which involved oak window and door casings, doors, transoms and other bits of Victorian interior trim it was perfect.
John D.
Reviewed in Canada on February 1, 2021
Every Bit as good as everyone says it is. Easy to use. Looks fantastic!AND Not made in China!
Judy Angel
Reviewed in Canada on November 24, 2020
It was the best stuff I’ve ever used
Cindy T.
Reviewed in the United States on January 2, 2013
I have done wood finishing for many decades. I've used mostly products from the local hardware, paint store and big box stores. I did some extensive research when I wanted to finish the woodwork in our newly purchased home. I have a 6,000 square foot home with a 25' ceiling in the great room. The home was custom built but was never fully finished, so all the door frames were unfinished, along with many of the doors, which totaled 25, 6-panel doors. I wanted to finish them in a dark espresso, satin finish and I wanted to see if I could find a product that would turn out looking as commercial as possible. After using some oil based products, before water based ones came into vogue, I switched to water based products. After using water based, exclusively, I decided to use oil-based products again, which have infinitely better outcomes than water-based ones. I took note from the professionals and noticed that General Finishes was used by many of them. I also purchased General Finishes Gel Stain in the color Java, and amped up the dark pigment with the color black from my set of Mixol Universal Tints. The results were exceptional. The gel stain went on beautifully as did the Arm-R-Seal topcoat finish. I've had a cabinet maker tell me that my work indeed looked commercial, which was a big compliment for me. I have used all the top brands on the market, but none compared to General Finishes. Even more than that was their web site which provides extensive information on preparation and application that gave me the confidence to undertake my project with high expectations and subsequent success. There are dozens of video tutorials available on the web providing more information than I ever wanted or needed. I especially targeted the videos since I am a visual learner. The only problem I had was working in an unrecommended warmer temperature. I also didn't like dealing with the protective wear like a cumbersome respirator. In the end, my woodwork looks wonderful and the finish is so hard and durable, that I know it will look great for many years to come. I highly recommend anything that General Finishes makes, which I might add, includes many water based products that also don't compare to anything sold by high volume hardware stores. The prices are higher, but are well worth it in execution and result. I buy the Arm-r-Seal in a gallon plastic container which pours out from a spout and is by far the easiest and most economical container to use. While General Finishes does sell to selected stores, there are none in my area, so being able to purchase online is a great option for me. The products come well protected as well.
Recommended Products
$28.99
$ 13 .99 $13.99