Your cart is empty.
Your cart is empty.4.3 out of 5 stars
- #20 in Projector Mounts
Product Description
Easy 3-Step Installation
Step 1
Mount the Ceiling Plate
Step 2
Attach the Projector to the Mount
Step 3
Assemble the Mount
Warm Tip
To prevent the mount from shaking,please tighten the screws marked in the picture above
Maciej
Reviewed in the United States on February 13, 2025
Fits my BenQ TK710 perfectly! Very sturdy!
Fits well, great hiking pants
Reviewed in the United States on July 11, 2024
It was recommended by an Amazon representative via chat to match my projector which it bought from Amazon. However, the attachment did not match the screw hole of the projector. This was very disappointing. Unfortunately,
Ed
Reviewed in Canada on December 24, 2024
Great quality, robust, does what it should for the length.
Johnny Shopface
Reviewed in the United States on December 2, 2024
The mount parts that go to the projector itself are actually pretty ingenius and flexible. I'd be surprised if you had a small or medium sized projector with holes 12 inches apart that this didn't fit. The little swing arms that you attach to the mounting holes go *under* the big spiral disc, which wasn't obvious at first, but once I got that sorted out, it was really easy to see how this could fit anything with 3 or 4 mounting holes, no matter where they were located, as long as they weren't miles apart.The mounting pole itself is plastic, not metal, and it does have some wobble to it, so if you're mounting it somewhere where it might get jostled around, or exposed to wind, this might not be the right mount for you. It works great for me, and we used the full 48" of extension.I read some reviews before buying where people said the mount or the swivel/tilt thing doesn't work, and I think it's safe to chalk that up to people not reading the directions or understanding what to do. This was actually really flexible and capable. I'm happy.
Johnny Dorrito
Reviewed in Canada on April 18, 2024
Bought this to support an Optoma GT2100HDR projector in a golf simulator. Went together easily enough, but it wobbles side-to-side when installed. 99% of the stresses will be downward and once in place, the monitor won't move...but it is absolutely not confidence inspiring to see this bracket wobble a LOT when you are attaching the projector to it. Also , none of set screws did anything... they just spun and spun without holding anything in place. Thing it is overpriced at the quality of the parts you receive, but adequate if you aren't looking to spend $400 for a ceiling bracket.
Bruno V.
Reviewed in Canada on September 30, 2023
Seems like a good sturdy product.. the only caveat is that the screws dont fit the mount. I have an Epson HC3020 and this does not fit. I will have to figure it out but not seller's fault. My only downside with this is the length of the arms.. I mean, come on, make em longer ffs...
Jess kovac
Reviewed in Canada on March 21, 2020
Product exactly as shown/ described and excellent customer service
Papa Pastie
Reviewed in the United States on November 24, 2020
The media could not be loaded.
Vijay V
Reviewed in the United States on January 25, 2020
I truly believe the product is well designed - light weight yet sturdy in designed. In-locking pipes are well built and doesn't allow for over extension and avoids any issues.Main issue for returning this item:==========================The top plate which we screw to joist had only 2 holes for screw insert, I would have felt much happier if it had placeholder for 4 or 6 or 8 screws if needed.This was the major problem for me, as I purchased a projector which weighs > 15 pounds, and I was super anxious with the 2 screw placeholder. Its felt like the my precious projector hanging on 2 screws - this might very well work for others people, but comparing to other mounts in the market, all of them provide 6-8 screw holders. I would appreciate if they can change the design to include more holes for additional screws.The extension pipes at the minimum are 23 inches, from the ceiling this causes the projector to bang on my head. I needed something which allowed me to make this smaller if needed - "this is fully my fault" as I didn't read the manual before purchasing.Other than excellent product, which I had to unfortunately return it.
Ives
Reviewed in the United States on October 31, 2018
Very good projector mount. High quality finishing, and come with a very detail instruction, it makes me so easy to install it. The adjustable arms perfect fit to my projector, they are working sturdy and safety.There are two things I would like other people to pay attention while installing your mount. First, complete all the connecting before installing to the ceiling!!! Second, Tightening the Screws Completely!!!During my installing, I installed 2 times. First time, I just connected all the screws, but haven’t tighten completely. I thought I can adjust them after install to the ceiling. The result is it’s too hard and tired to adjust the screws up on the ceiling, even I feel them were tightened, but the projector still shaking. So, I have to take them off, tightened all the screws completely before installed to the ceiling. The second time everything went well, after tightened all the screws, the base, the extension pipe, and the bottom are all sturdy and work perfect.Above is my experience of my installation, hope my sharing can save your time and make things easier.Overall, this projector is made of high quality material, very durability, and versatility. I will recommend to my friends.
Retired Engineer
Reviewed in the United States on October 31, 2018
My home theater has a 12 ft ceiling and the top of my projector screen is at 7 ft, so I need to mount my projector at about 4 ft from the ceiling to minimize aggressive keystone corrections, which degrade image quality. This projector mount is the only one that meets my height requirement. It is made of high quality materials and is rigid enough at full extension for my BenQ HT2250 projector which weighs more than 9 lbs. I found it easy to set up and make adjustments. You might notice in the attached photo that I fastened a piece of wood (2" D x 6" W x 32" L) to the ceiling beams then attach the projector mount to the wood so that I could align the projector lense to the center line of the screen. This setup works out very well for me. The customer support is great. I contacted the seller for some missing hardware (a few screws) and they promptly sent me a complete projector mount. I highly recommend this mount especially if you have a tall ceiling.
Recommended Products