Your cart is empty.
Your cart is empty.Product Description
Measure OUTSIDE DIAMETER of pipe to ensure proper sizing.
Flashers brand pipe flashing is the ONLY pipe flashing 100% Made in the USA
Jackman Industries is a family-owned small business that employs an American Workforce. We have proudly manufactured our product in Salem, Oregon since 1992.
Credentials:
- Women-Owned Small Business
- Registered Small Business
- OR: MWBE - Minority and Women-Owned Business Enterprise
- OR: ESB - Emerging Small Business
- OR: DBE - Disadvantaged Business Enterprise
- CA: CPUC Clearinghouse
Please review the intended design use and applicable temperature ranges prior to purchase. Product failure may occur if used outside these parameters.
Flashers brand pipe flashings are intended to create a water-tight seal on pipe penetrations through metal roofing and siding. Flashers are NOT recommended for use on applications that exceed continuous temperature ranges, as listed. Ex: Single Wall pipe with Flashers pipe flashing mounted close to heat source. Product failure may occur with temperatures exceeding applicable ranges. Use on projects out of the scope of the intended use or temperature range will void any possibility of manufacturer replacement.
Please review the intended design use and applicable temperature ranges prior to purchase. Product failure may occur if used outside these parameters.
Crystal Miller
Reviewed in the United States on March 13, 2025
We used them to vent our bathroom fan out of the room. It works very well and is easy to install.
gaetan nenquin
Reviewed in Canada on February 17, 2025
A très bien fonctionné pour un mini wood stove avec un pipe de 7cm, je l'ai eu 2 hivers complet dans une rollotte transformée en tiny house et très satisfait
Thomas
Reviewed in the United States on September 25, 2024
Sealed to the roof. Ease to install .
Customer
Reviewed in the United States on February 15, 2024
Very surprised by the sizeIt's flimsy and not much there to screw intoPrice is high
Renee
Reviewed in the United States on December 9, 2024
Adjusted to all three of our requirements of ur roof vent sizes.
dennis stephenson
Reviewed in the United States on December 12, 2024
Looks nice and great quality
Fudsky
Reviewed in Canada on November 13, 2024
Well made fit my 8" b vent pipe for my wood stove
Christian eiklor
Reviewed in the United States on October 13, 2024
She works gotta use your silicone but she works!
Michael
Reviewed in the United States on January 29, 2024
Good replacement for my old boot. Sealed good, we’ll see how long it lasts? I added a metal shroud above it on the pipe to protect it from falling debris like hail and other natural disasters.
Terry la france
Reviewed in Canada on July 9, 2023
good
Cindy
Reviewed in Canada on May 19, 2023
According to my husband this was exactly what he needed..
Claude Robert
Reviewed in Canada on January 15, 2023
Installer pour la cheminé de la maison. Très étanche.
Cooper
Reviewed in the United States on January 10, 2022
Common sense is needed for installation. Caulk, check! Self tapping screws, check! Common sense, check! I slid it onto my double insulated pipe to see where I needed to trim it and then did so. Secured my double insulated pipe on the inside with my metal strapping I purchased. Again, use of common sense is required. I only mention this after reading other reviewers comments. After pipe secured, I used a little WD40 on the pipe which helped it slide over the pipe. When it was in place I molded it around my metal siding. I used it on the side and not for a roof application to help with not have leaks later on down the road. I used “Through The Roof” silicone and then slid the sleeve up to the siding. Then secured it with self tapping screws for a nice tight fit. Afterwards, I ran a bead around it to make sure it was sealed up and no water can leak through. Super happy with the product and would purchase again.
Recommended Products