Your cart is empty.
Your cart is empty. Specification:
Item Type: LCD module
Size: 3.5in
Type: TFT
Driver Chip: ILI9488
Resolution: 480x320(Pixel)
Module Interface: 4-Wire serial peripheral interface
Effective Display Area(AA area): Approx. 49 x 73.4mm / 1.9 x 2.9in
Size of for PCB Bottom Plate: Approx. 56.3 x 98mm / 2.2 x 3.9in
VCC Power Supply Voltage: 3.3V~5V
Logic I/O Voltage: 3.3VTTL)
Package List:
1 x LCD Module
1 x Touch Pen
Note:
Please note that the new type and old type of this product will be sent randomly and make sure you will not mind before ordering.
Eduardo T.
Reviewed in Mexico on February 15, 2024
Funciona perfecto a 3.3v
Terry Cornall
Reviewed in Australia on May 29, 2023
I saw reports that you needed to be careful with not using the MISO signal from the LCD because it got held even if the LCD was not selected. It isn't needed for LCD so I just left it disconnected on the LCD port. But when I tried to get the SD card to work, it wouldn't and I traced it down to the MISO signal on the SD port apparently not getting to the SD card holder at all!. After I added a wire to connect MISO the SD worked.Not only that, but I found that the resistive touch sensor had irregularities such that the centre columns and row responses were very non-linear and required a custom calibration even after the usual calibration of the corners.I do not recommend this product. You can make it work if you try hard, but there are better choices.
Daniel R.
Reviewed in the United States on May 12, 2023
Two versions ship The most up to date version , do not connect SDO (MISO pin next to the LED pin) or touch does not work, even though that pin is a display pin. Old version works even if SDO is connected, but should also work without it. The new version (The one I got anyway) has yellow plastic on the soldered pins. Some microcontrollers require a 10K resistor connected to 3.3 V on from each of the cs pins you have connected to the microcontroller as CS pins. (One for CS display and one for CS touch). Runs great on my teensy 4.1. (I used the ILI9488_t3 libray which only works on teensy boards, but have also gotten it to run with other boards using other libraries) Enjoy!!!
Robert J Rusek
Reviewed in the United States on April 23, 2023
Seller would not replace product said it was out of warranty.
J H S
Reviewed in the United States on September 3, 2022
The part arrived same day from Amazon. The display is nice with the 3.5 inch display. There are plenty of example programs for the ILI9488 controller it uses in the teensyduino arduino IDE libraries. The touch interface uses an XPT2046 controller. A couple of items I had using the display. The "DO_MISO" pin on the TFT section is not needed to display information. If connected to the SPI bus it, stopped the MISO line, so I do not connect it. It will keep other devices on the SPI bus which need MISO, such as the touch interface and SD card interface, from working if it is connected. The example programs I have used, connected to teensyduino 3.6 or 4.1 development boards ( 3. 3 volt boards ), some using the TFT screen, touchscreen and SD card at the same time, have worked OK.
V. Wheeler
Reviewed in the United States on July 4, 2022
Came packaged in ESD bag wrapped in bubble wrap and in it's own cardboard box.I am using it with the ThingPulse Custom Connector PCB from a weather display kit to connect the ESP8266-WiFi and the TFT display of course because of it's larger size the mounting holes do not aligned not a problem for my use. The electrical connection works well for my project. Seller took the time to contact me through Amazon to verify the touch display was received and ask if there were any issues.
Recommended Products
