Your cart is empty.
Your cart is empty.Equus 2" Electric Oil Pressure Gauge measures the oil pressure from 0 - 100 PSI (0 - 70 kPa) of the engine. Also features a bright backlit display for enhanced night viewing in one of four colors and 90° sweep for quick readings. Rear twist-on ring mount and included hardware and adapters make for an easy, basic installation in most foreign and domestic vehicles.
Festus
Reviewed in the United States on September 17, 2024
Make sure the ground is to a piece of structure on the gauge check with continuity signal. The sender is easy 3 to 4 wraps of teflon and put it in.
Duane M
Reviewed in the United States on August 16, 2024
I’ve had it in a 65 ford 200 for a while and it works well
Susan C
Reviewed in the United States on July 11, 2024
Decent quality gauge, good price, works great. Overall very happy with this purchase.
Jim Vilseck Jr.
Reviewed in the United States on October 22, 2024
Very Nice!
CTC
Reviewed in the United States on September 2, 2023
This is a really nice gauge. Please see all the photos I’ve included. The color is actually slightly off-white. The gauge comes with the red green and blue covers for the lightbulb. However, I wanted to put in LEDs. Here is the Amazon description for the LED bulb that fits these sockets and although it says, RED in the description you can get several different colors from the same link.LETINGFAR 194 LED Bulb RED Pack of 10, T10 led bulb, 168 2825 W5W T10 Wedge COB LED Replacement Bulbs Error Free for Car Dome Map Door Courtesy License Plate Lights.The color and brightness looks much more even and not as glaring in person. The bulbs are self-contained and only require 12v positive and negative hook up.
superman
Reviewed in the United States on October 18, 2022
easy to install and works very well and looks great in my hot rod.
A.j. Tedeschi
Reviewed in the United States on September 12, 2021
Used on 93 s10 with 4.3 v6.As I said ground case of oil sender .Use a hose clamp on sender, a length of wirestrip one end about 1/2" place it under clamp,tighten securely,place a lug on other end and attach to engine oil pan.No leaks and perfectly grounded. System works great.
Evan
Reviewed in the United States on January 3, 2019
Purchased for a 2003 F150 XL. Gauge comes with everything except the wire lengths needed to connect (not uncommon). Sending unit is a two wire design; one for the gauge and one for a warning light if your vehicle is so equipped. Three terminals on the gauge itself; ground, power, and sending unit. The light is incandescent (not LED) and uses a separate wiring harness.I use an oil filter adapter plate to provide terminal ports because the factory port in the block is too inaccessible for an aftermarket sending unit. This adapter plate is powder coated. This is critical because the sending unit must be grounded to the engine block to complete the circuit. It says in the instructions, "do not use thread sealant or Teflon tape." There is no way to connect a bonding strip or jumper wire to the sending unit to complete this ground circuit. The unit is grounded when it is screwed into the engine block.This is a problem because the oil filter adapter plate is electrically isolated from the engine block because of the rubber gasket between it and the oil filter mounting location on the engine block. Additionally, I suspect that the powder coating on the adapter plate further interrupts the ground connection.Gauge was installed but readings were erratic or sometimes non existent. It's very likely that this was a grounding problem. If you use an adapter plate to provide sending unit ports, you may have the same problem.Additionally, I mounted this gauge in an A pillar gauge pod. Because this gauge uses a threaded collar for installation, fitment within the pod was tricky, at best. Not the best gauge for this type of mount.
Recommended Products
