Shopping Cart

Your cart is empty.

Your cart is empty.

Energy Suspension 9.8141G Shock Bushing Set , Black

Free shipping on orders over $29.99

$8.60

$ 4 .99 $4.99

In Stock
  • Durability is superior for cars, trucks and SUVs; road salt, oil, and a host of other common under car contaminants will eventually destroy the rubber bushings on your vehicles, not to mention the weight and torque forces that typically compress rubber
  • Hyper-Flex replacement polyurethane components stand up well to contaminants that often destroy rubber and have been engineered to give longer-lasting performance and not compress permanently 5/8 Inch I.D.,1 1/8 Inch O.D.,1 1/4 Inch Long,2 Bushings Per Set
  • Hyper-Flex is offered in a variety of durometers (firmness or softness), depending on product application; performance tested and race proven; used for all of Energy Suspension products that require a higher level of performance and durability
  • If you are modifying, building a new vehicle for scratch or restoring an old one, Energy Suspension's Hyper-Flex performance polyurethane should be the 'ground zero' focus of your present and next vehicle plans
  • Over two decades of in-house experience in innovating, engineering and formulating wide selection of polyurethane components for many different industries, Energy Suspension has qualified as premier manufacturer of the high quality polyurethane products


ENERGY SUSPN Energy Suspension 9.8141G Shock Bushing Set , Black


Johnnymac
Reviewed in the United States on September 14, 2024
Good quality
Dana Goulston
Reviewed in the United States on June 28, 2024
Material was too hard and impossible to instal into the shock openingl. Stock bushings are softer. However, seller was gracious and said to just keep them while still giving a refund, so that's a plus.
J.Test
Reviewed in the United States on May 18, 2024
I’ll keep this simple; Yes, they fit Jeep XJ and TJ shocks.
Customer
Reviewed in the United States on October 13, 2024
If your wanting a stiffer suspension than look no other. This product greatly enhanced my suspension and gave it a nice tight n race car feel i needed. Would recommend to freeze them over night for ease of installation along with some grease when installing. If ya have a press even better but hand tools will work just fine.
Benjamin Cellitto
Reviewed in the United States on May 13, 2023
Good bushing for a good price.
Steve G.
Reviewed in the United States on May 17, 2021
These bushings worked great however, I didn't use them for their intended application. I needed two shock bushings for my Ski-Doo Blizzard MX but these were too big, but I knew they would be. Using a bench grinder, I carefully removed enough material to make them fit perfectly. Fit nicely and shipped quickly.
M.O.B.
Reviewed in the United States on June 8, 2020
The other day I noticed some noise while driving my 2008 E250 and after inspection discovered rubber bushings on my shocks completely disintegrated. I was ready to replace them but turned out they were as good as new and it would be a shame to throw them away. I bought this set and after about an hour and a half spent I had them installed. They were a tight fit, just as they should, and I highly recommend to use a good amount of grease and a wise to put them in. For some reason they didn't come with metal inset tube like original bushings and original were destroyed so I had to run to my local hardware store and get replacement.Very happy with results and if you mechanic enough you can DIY.
Customer
Reviewed in the United States on December 17, 2019
So I needed just the bushings for my rear shocks on my 2006 Ford F250 4x4 diesel. Figured I'd take a shot on these because they were so cheap. The ID of the bushings fit perfectly. The OD of the bushing was close enough (ever so slightly larger). I had to only lightly grind the tapered part so you could get it started into the shock and with a little WD40 and a large C-clamp I was able to press them in. No more rattle in my truck and didnt have to spend the money replacing my otherwise good shocks. Would absolutely buy this if you are looking to replace yours in your F250 and have a grinder and a vice or c clamp handy.