Your cart is empty.
Your cart is empty.Product Description
Made of high electrical conductivity copper
Directly welding without scraping isolation layer
Used in professional maintenance of mobile phones, computers, laptops and other precision motherboard
Note
1. Please allow some error due to manual measurement. Thanks for your understanding. 2. Monitors are not calibrated same, item color displayed in photos may be showing slightly different from the real object. Please take the real one as standard.
Each wire is about 12 meters long, enough for home or shop use
Made of high electrical conductivity copper. Used in professional maintenance of mobile phones, computers, laptops and other precision motherboard. A copper wire to take place of wire cable. Directly welding without scraping isolation layer. Each wire is about 12 meters long, enough for home or shop use.
Enameled wire is a copper wire coated with a very thin layer of insulation. It is used in the construction of transformers, inductors, motors, speakers, hard disk head actuators, electromagnets, and other applications that require tight coils of insulated wire.
R Cull
Reviewed in the United States on January 5, 2025
I needed super thin wire to fix some PCBs and this works great for that micro work. As described and works great.
Dave Cooper
Reviewed in the United States on July 20, 2024
It is smaller diameter then I thought it would be. It works but is difficult to work with.
Anthony Prince
Reviewed in the United States on March 16, 2024
Comes with 5 micro rolls. Four were fine one was almost empty. I would not recommend buying this.
W. Tomlinson
Reviewed in the United States on June 2, 2023
The quality of the wire seems ok, just make sure you understand just how small this is before you buy it, it truly is for trace repair more. If you are searching for enameled wire for soldering short jumpers on electronics, this is probably not going to work for you [it didnt for me, even though I tried to make it work, but I could not get the wire to make continuity between the two pads I connected it to. Could have been user error but seemed the enamel didnt want to melt away to expose the wire, which is good for long runs but makes it bad for short ones]. It really is 0.1mm as the listing states, or approximately 38 gauge, which is hard to visualize in the pictures for those who have no concept of it, so check the comparison photos I posted for the review. If you need to rewrap a small electromagnet or repair a long trace then this could probably work, but for repairing distances under a centimeter on a PCB this is simply too small to recommend [see pictures showing this wire on the bottom with 2 strands of thermistat wire above it (18 gauge) which I ended up using a bit of for my project though it was bulkier than I wanted for the task, and a photo comparing to 0.6mm solder (appx 22/23 gauge)]. I took away a star because it seems like the wire just doesnt want to make a true connection at a super short distance, and I didnt want to risk shorting to other components in the way bu pre burning all the enamel [and defeating its purpose], but for longer runs it would probably work just fine.
Patriot
Reviewed in the United States on May 23, 2023
Didn't know the wire was going to be so small we also waited forever to get it
Cap America
Reviewed in the United States on March 9, 2023
Great wire for tracing. I used it to buy pass a board fuse.
WickedStorm
Reviewed in the United States on January 10, 2023
These are small (sewing bobbin size perhaps) more than enough product to probably last the rest of my life rebuilding traces and small jumpers.. a great ... IF ALL ELSE FAILS!
Kurtis Bigelow
Reviewed in the United States on December 29, 2022
So far this copper jumper wire works as intended. I have tested a few jumpers on an xbox one s and it was successful.
Recommended Products
$14.75
$ 6 .99 $6.99
$172.83
$ 71 .99 $71.99
$48.25
$ 20 .99 $20.99