Your cart is empty.
Your cart is empty.Drill America high-speed steel bridge reamer used to align existing holes prior to bolt or rivet installation. Point is tapered to permit entry into overlapping holes. Three symmetrically placed flats on shank provide positive grip in portable electric and pneumatic tools. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Used to align existing holes prior to bolt or rivet installation.
Jenni Lozano
Reviewed in the United States on January 9, 2025
Good value for money. Buy 2 went dull after went thru hardened steel in 93 jeep frame. Tap it with a hammer drill bit was accurate.
Swimmer
Reviewed in the United States on July 8, 2024
It may be ok for light duty work, but absolutely worthless for anything more heavy duty. It could not turn one single 1/2” hole into a 3/4” on 5/16” steel plate with proper RPM and lubrication. Don’t waste your time and money on this.
Customer
Reviewed in the United States on October 11, 2024
great quality
Martin
Reviewed in Canada on April 18, 2024
Pour agrandir un trou, c'est idéal
Lucas
Reviewed in the United States on July 13, 2023
Reamer worked perfectly on 3/8 mild steel but needed a surprising amount of power to run it. Neither 8 amp corded milwaukee or drill press wanted anything to do with it. Old school gear reduced hole hog didn't mind it though. Just had to be careful not to bind the bit and he plenty of lube. Only did 6 holes so i can't comment on longevity.
S. Crosby
Reviewed in the United States on October 15, 2023
This thing got the job done. Never used one before. I needed to ream six holes on a power rack and attachments. I didn't know what to expect. I ordered it plus some cutting fluid. (Don't try it without that.) But, it cut through the steel pretty much like butter. Finished the job in five minutes. I'll never need it again and wish that I could sell it to someone.
zelda2011
Reviewed in the United States on September 24, 2022
Couldn’t get the holes for my new fifth wheel hitch to line up exactly. I got 7 of them myself but 3 wouldn’t go perfectly.This bit did the trick just like in the video. Totally worth the cost just for three holes because it saved SO much time! Zip and it was done.Be sure you have a drill that can take a 1/2 inch bit.
EMR
Reviewed in the United States on September 20, 2022
I had a 1/2" hole in 1/2" thick steel and I needed the hole to be 5/8". I'd already broke a drill bit trying to get 1/16" on each side oversized with a 5/8" drill bit, and it was really grabby and hard to do...so I found this reamer and went very slow with tap magic cutting fluid, and it worked like a charm.
John Beatty
Reviewed in the United States on December 10, 2022
I had 12 chain sprockets on a 1" shaft that had a through-bolt drilled in. The hole had become worn, so I decided to drill them up from 5/16" to 3/8"and pin them with a steel roll pin. The problem was that everything had to be in alignment, which could not be done on the machine with a conventional drill bit. I thought of a standard reamer, knowing the hardened shaft would trash it quickly. Then these popped up! Not only did it perform flawlessly in alignment, but it drilled out all 12 (cast steel sprockets/hardened shafting) and wanting more! Also, as the spiral is a reverse, it pushes away the chips rather than draw it into the work and jamb it. Every shop should have these!
fred
Reviewed in Canada on February 9, 2021
Not the best quality, barely got the job done before it broke
Aaron
Reviewed in Canada on June 30, 2019
The product I received had been used before as there was a notch in the flutes all the way around. Otherwise it works perfectly. I will buy another
Recommended Products
$104.61
$ 43 .99 $43.99