Your cart is empty.
Your cart is empty.This PCV valve grommet is designed to match the fit and function of the original grommet on specified vehicles, and is engineered for durability and reliable performance.
Customer
Reviewed in Canada on February 3, 2025
perfect fit 2.7 tacoma
Roberto
Reviewed in the United States on February 16, 2025
Bueno
kenzy
Reviewed in the United States on August 18, 2024
Seems like a fine replacement part. Does what it should. Good to have when changing pcv valve because the old one was very hard and brittle.
Ben
Reviewed in the United States on December 4, 2024
Shape and size like OEM grommet. Fit perfectly on 2001 Sequoia 4.7L engine.
Taylor Fam
Reviewed in the United States on December 22, 2024
Replace this and PCV at the same time.
Josiane fratino
Reviewed in the United States on April 3, 2024
I read the bad reviews and what I did is that I put the ring into the hole then used a bit of Lubricant to put the new PCV valve on
cs
Reviewed in the United States on April 3, 2023
I ordered this grommet for a '98 tacoma 4WD 3.4L V6 5VZ-FE. Despite seeing the other bad reviews, I figured I'd give it a try, assuming that the problems people were reporting were due to user error or just bad luck.However, as others have stated, these are terrible grommets. First of all, the inner diameter of these grommets is far too small when compared to the OEM grommet. So, you'll need to apply a lot of force in order to try to get the PCV valve into it. At this point, the grommet will most likely tear & break, as the rubber is brittle & of very cheap quality. I lubricated the grommet & tried my best to not overdo it when trying to install the PCV valve, but it still ended up tearing.I'm convinced that these grommets are either from very old stock that were stored improperly, or from a defective batch, and that they're being sold for cheap here on amazon in the hopes that most people won't go through the troubing of trying to return them based on the low price. It's either this, or Dorman has simply screwed up in their design and/or their 'application designation' for these grommets, because these clearly won't work for all of the Toyota models that they are claiming.I ended up returning this grommet & buying the OEM grommet directly from Toyota, which wasn't much more in price than this one. Save your time & money and avoid these. Buy another brand or OEM.
Quality and Frugality
Reviewed in the United States on May 24, 2022
Good replacement for old loosened or cracked grommet on 2001 Tundra 4.7 on drivers side front valve cover. Be careful removing old one may crack and pieces may fall inside valve cover. Use some good needle nose pliers bend inward and pull out. May come out in pieces. Also using a headlamp for direct visualization is helpful and you can see if pieces fell in valve cover. Once new one is in it will fit valve cover and pcv valve perfectly. Do not think is worth money to buy Toyota brand grommet This is very inexpensive and worked fine. The pcv valve itself can just be cleaned with carburetor cleaner and reused. Unless you want to buy a new one - just because. The hose was starting to crack on both ends. Trimmed off 3/4 inch on each end but then was a little too short - still worked but decided to replace while was there and was now too short. 1/2 inch trim on each would have worked.
Tom Davies
Reviewed in Canada on December 3, 2022
Good value
Keun Woo Park
Reviewed in Canada on December 22, 2022
Price is so cheaper than oem but quality is like a oem thumbs up
Morgan Journey
Reviewed in Canada on November 22, 2022
The product arrived with a tear in the rubber so basically useless
Jerrod (Jake) E. McCann
Reviewed in Canada on June 8, 2021
Fast shipping, perfect replacement for 1UZFE, Left Bank PCV valve grommet. My application was for a 1995 Lexus SC400.
E.G
Reviewed in the United States on August 18, 2020
Got a new PCV valve and the OEM grommet ripped as I was trying to remove the old valve. Installed this new grommet along with new PCV valve. Good as new
Recommended Products
