Your cart is empty.
Your cart is empty.Protect the braking system from debris and corrosive weather conditions with this rust-resistant replacement brake dust shield. Dimensional verification and salt spray testing ensures proper fit and extended service life. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Buick Century: 1978, 1979, 1980, 1981] - [Buick Regal: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987] - [Chevrolet Camaro: 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992] - [Chevrolet El Camino: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987] - [Chevrolet LLV: 1987, 1988, 1989, 1990, 1991] - [Chevrolet Malibu: 1978, 1979, 1980, 1981, 1982, 1983] - [Chevrolet Monte Carlo: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988] - [Chevrolet S10 Blazer: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992] - [Chevrolet S10: 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992] - [GMC Caballero: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987] - [GMC Jimmy: 1992] - [GMC S15 Jimmy: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991] - [GMC S15: 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990] - [GMC Sonoma: 1991, 1992] - [GMC Syclone: 1991] - [GMC Typhoon: 1992] - [Oldsmobile Bravada: 1991, 1992] - [Oldsmobile Cutlass Calais: 1978, 1979, 1980, 1981, 1982, 1983, 1984] - [Oldsmobile Cutlass Cruiser: 1980, 1981, 1982, 1983] - [Oldsmobile Cutlass Supreme: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988] - [Oldsmobile Cutlass: 1978, 1979, 1980, 1981, 1985, 1986, 1987] - [Pontiac Bonneville: 1982, 1983, 1984, 1985, 1986] - [Pontiac Firebird: 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992] - [Pontiac Grand Am: 1978, 1979, 1980] - [Pontiac Grand LeMans: 1978, 1979, 1980, 1981] - [Pontiac Grand Prix: 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987] - [Pontiac LeMans: 1978, 1979, 1980, 1981]
shopper1
Reviewed in the United States on January 9, 2024
Good quality backing plates. The only issue I had with them is the factory hole for the anchor pin was a little too small. It did not take much to ream it out for a good fit.
David Shaw
Reviewed in the United States on August 14, 2021
Ok product typical Chinese made not exactly like the American made plate but can be used. You have to drill holes or mounting and has an indentation where it should be flat at the top.
Paul Fredricks
Reviewed in the United States on March 30, 2021
The Brake Backing Plate was the right size and shape. I needed only the anchor bolt. I wish the bolt was sold separately.
redpineshomestead
Reviewed in the United States on January 16, 2021
Only 2 holes for mounting to axle housing then they do Not match even close. HaD to drill all 4holes to mount backing plate to axle housing.. would NOT RECOMEND BUYING this PRODUCT...... then brake stop is NOT CORRECT ONE FOR THESE SHOULDER ON BOLT WIDER THAN BACKING PLATE WILL NOT TIGHTEN DOWN WITH NUT SUPPLIED. JUST PISS POOR EVERY THING. DON NOT BUY THESE.
Racoon69er
Reviewed in the United States on March 31, 2020
Worked good as expected
Adkins
Reviewed in the United States on December 12, 2019
Wrong size, so sending back. My fault.
Customer
Reviewed in the United States on May 16, 2018
AA
Customer
Reviewed in the United States on October 23, 2016
Great service part for an older truck. Every bit as good as the O.E. @ a great price !
Recommended Products
$45.88
$ 21 .99 $21.99
$44.77
$ 22 .99 $22.99