Your cart is empty.
Your cart is empty.Instructions: 1. Open the filling cap and fill the unit using a funnel; 2. Tighten cap and connect dispensing hose; 3. Use the correct adapter then insert into the transmission opening after draining used oil; 4. Use soft grip pump handle to pump liquid from the filler unit to the vehicle; 5. Pressure gauge helps to gauge how fast fluid will move. Specifications: Condition: Brand New Color: White Pressure: 0-85 PSI (0-6 bar)
Customer
Reviewed in the United States on February 25, 2025
Must have for diy a little slow to transfer fuild but it works
Mark
Reviewed in the United States on February 17, 2025
Plastic tool to open fill cap is too small to fit cap. Correct adapter I needed, pumped up and delivered fluid as expected. Vale and quick connect worked well on hose end. Hose easy to move around, very flexible. Overall a usable product, would buy again...
Barny bruno
Reviewed in Canada on January 31, 2025
Tte bon
Winston
Reviewed in the United States on January 20, 2025
Works very well looking forward to do business again
David Stagg
Reviewed in the United States on January 1, 2025
much higher quality than I expected for the very reasonable price, many adapter fittings for various vehicles.Highly Recommended
Joshua N.
Reviewed in the United States on September 17, 2024
Solvents and thinner fluids this works great for. I tried it on some thicker oils however and it was a very slow process. So just stick to the thinner stuff and it will work fine.
Charles Willoughby
Reviewed in the United States on September 14, 2024
Used it to pump fluid into my "sealed" 09 Explorer (no dip stick). Worked fine. Especially like the ability to pressurize the tank before crawling under the vehicle to add the fluid.Minor complaint...the plastic "wrench" they sent to tighten the filler cap is too big for the cap. It will not tighten the cap. But, hey, that's why they invented channel locks! 12/16/24 - Just used it to pump in 75/140 gear oil into my rear diff. Hook type end "nozzle" was especially helpful to hook the hose into the fill hole.
Johnny L.
Reviewed in the United States on December 3, 2024
Interesting how car manufacturers are doing stuff now?
kris
Reviewed in Germany on December 22, 2024
Falls sich jemand fragt welches Gewinde man für den keinen Kugelhahn braucht, falls man es etwas modifizieren möchte - es ist G1/4 auf beiden Seiten. Da ich das Getriebeöl mit Hilfe von einem Wagenheber tue, ist der Schlauch für mich etwas kurz, es reicht zwar, aber dann steht das ganze buchstäblich am Rad dran, es sei denn man würde noch das Rad abmachen, dann wäre es mehr als genug.Hatte keine Probleme mit dem Gerät, allerdings fand ich es einfacher und besser Öl durch die große Öffnung hineinzukippen.Sehr zufrieden mit dem Kauf.
Customer
Reviewed in the United Kingdom on November 23, 2024
The pump worked well, it was used to refill ZF 8 speed automatic gearbox, so the attachments came in handy. All of the accessories and tools supplied were of good quality as is the pump; geat value.
Tom Nibourg
Reviewed in Canada on October 22, 2024
Very surprised at the quality. End fittings are metal, hose is soft and flexable. Used to fill 2023 ram trans.
Shane Swartz
Reviewed in the United States on October 1, 2024
So this worked good for me yesterday while using it, then when I was done I released the pressure and set it aside. Well, this morning I went out to a huge leak of ATF all over my garage floor. Upon further inspection I saw the hose has literally fell apart from the handle part of this kit. To make it worse, the ATF was all over my garage doors rubber seal and dripped on to me as I stood under it, staining one of my expensive shirts. Not a happy customer.
Recommended Products
