Your cart is empty.
Your cart is empty.Product Description
DAP Touch 'n Foam Max Fill is the original Touch 'n Foam sealant formulated to fill gaps and voids all around the home. Max Fill provides three times the expansion to fill gaps greater than 1 inch wide. Its weather-resistant bond seals out drafts while blocking insects and other pests. It can be used indoors or outdoors, is paintable, and comes with a reusable adapter, saving the can for multiple projects.
From the Manufacturer
In the familiar green can, this is the original Touch ’n Foam sealant formulated to fill larger gaps and voids all around the home. This super-expanding foam creates an airtight, weather-resistant bond that seals out drafts.
DAVID
Reviewed in Mexico on November 20, 2023
Buena calidad
DeborahAnne
Reviewed in Canada on July 24, 2021
The design of the nozzle with straw is useless. I couldn't even get through half of each can and it stopped working. For the price I expect more. I wouldn't buy or recommend this to anyone...ever.
Marie
Reviewed in Canada on May 17, 2021
It does get a lot bigger!
Larry K
Reviewed in the United States on August 10, 2020
I have used a lot of different expanding foam products over the years, to fill void and seal around entries into my home and honestly this product is about the same as all the others I have used. I bought it, as it was advertised and the can boldly proclaims it is re-useable. I hate buying a can, using it once and throwing the rest of the can away, as the application tube is plugged up. The instructions clarify the reusable term, saying the dispenser can be re-used up to 3 weeks. I followed the directions to kink the "straw" and put the end of the little nub on the top, to seal the end of the straw and then went to use it again after less then a week and the straw was plugged up solid and cold no be used... so much for re-useable.Good Product, if you don't plan to go back and re-use it a week or less later...
The Compari-Shopper
Reviewed in the United States on July 24, 2018
Part One: FOR EVERYONE: HOW TO ASSEMBLE THE CAN WITHOUT WASTING THE PRODUCT OR GETTING FRUSTRATEDSome of the reviewers have complained that when they attach the tube, the green metal can starts spraying before they can get the clear tube on the white nozzle all of the way (there are just these three pieces), making a mess and wasting the product. I ran into this too but found an easy solution with my second can: attach the clear straw/tube to the plastic white nozzle (specifically, over the rounded protruberance with a small hole in its end, which is opposite of the threaded indentation on the nozzle where you will screw the nozzle to the can) before you attach the nozzle to the can.With the straw safely and securely in place, it’s just as easy to screw the nozzle onto the can as if the straw were not attached. And now you don’t have to worry about the insulation spraying out as you put pressure on the straw to get it firmly onto the protruberance (sorry I can’t think of a better word even though I’m sure there are many).Part Two: FOR SEWISTS ONLY: HOW TO USE THIS PRODUCT TO MAKE A DRESS FORMI used this product for unconventional purposes. I covered myself in (1) body oil, (2) newspaper, and (3) masking tape from the waist to the ankle on one side and the waist to the mid-thigh on the other side. Then I cut down the side of the full leg and squirmed out of the “form” I made of my lower body. I used duct tape to tighten up any loose spots, then I sprayed this inside the empty form.It does expand quite a bit. I would guess that it does expand to three times its size but not more. I put a little too much in it and it burst the seams in one part of the leg. I recommend that you seal your seams tightly with duct tape after you apply this insulation product. I also recommend that, contrary to tutorials I’ll recommend below, you do NOT close the ankle or leg so that if the product expands more than you expected, it has somewhere to go other than out through a seam.Bottom line: I have a lower-body “dress form” that I can use to try on pants I am sewing for myself without having to get undressed over and over, or sew in my underwear. You can do the same thing with your upper body.Recommended Tutorials: for the upper body, there is a tutorial on the Threads Magazine site (they have four but only one uses the foam insulation method).For the lower body, see the tutorial on YouTube, “How to Make a Dress Form for Pants” by noelnova. Highly recommended. But I also recommend you get some duct tape because the masking tape listed in the tutorial just isn’t strong enough for some high-stress places, especially if you are doing it yourself and have to move around while the tape is on you.I needed four cans to make my pants form.
Ron
Reviewed in Canada on May 6, 2018
Works well
Bernvill
Reviewed in Mexico on June 29, 2017
Mucho mas fácil de usar que algunos otros productos, el aislamiento térmico es notable.La utilice para aislar una hielera para cocción basada en agua (sous vide) y funciono realmente bien.Es importante notar tres puntos:1) La espuma se expande sin importar obstrucción, esto hace que pueda romper lo que este rellenando. Es mejor hacer el proceso varias veces con un volumen bajo de espuma2) La espuma necesita humedad y luz para curar bien. Si se usa en un espacio seco sin luz, se convertirá en un fluido color café sumamente desagradable y difícil de limpiar. Es necesario aplicarlo en capas si no estará del todo expuesta al medio.3) Humedecer la superficie antes de aplicar!!!
Tom G.
Reviewed in the United States on July 15, 2013
This product dries fast and hard, which is what I needed for my little job. It is somewhat messy (they all are), but it dispenses at a rate which is manageable, so the stuff doesn't go flying all over the place. It comes with a 5-inch tube and lever-controlled release valve which makes it convenient to use. When the job is finished, the tube doubles back on itself and fits onto a small protrusion on the top of the valve for storage. I have not tried to use it again, so I don't know if this idea actually works. Here is a little side comment--I used this same kind of expandable foam several years ago to fill in the space underneath a fiberglass shower stall which "gave" when you stood in the shower. The foam expanded, dried hard, and made the floor of the shower solid, and no doubt prevented cracks from developing due to the flexing of the floor.
John S.
Reviewed in the United States on March 26, 2013
I purchased this Foam about 2 weeks ago and wanted to use it before reviewing it.I applied it to the area around a Medicine Cabinet (1.5-2.0 inch space around cabinet and also to a few window frame bottoms (exterior windows).I live in an old home.One thing is for sure...getting use to the pressure when pulling the "Trigger".Start with not to much and increase as you go...it is common sense.I really blasted it around the Cabinet and sanded it the next day.To cut down on the sanding that would have taken time I used a serraided knife and cut the now hard Foam about a quarter a inch,or less,from the top,bottom and sides.I used wooden block wrapped with sandpaper (level sanding) and the results were just what I wanted... A Perfect,non-noticeable (after painting) space that use to be almost 2 inches around this Medicine Cabinet! Its no appears that there was NO SPACE AT ALL!This was the 1st time that I have used any Expanding Foam and I intend on getting more.I worked for years before retiring and the 1st thing to remember is SAFETY (Read the Directions)Please Note - One should never go completely on anothers'Review.It is like a Movie Critic Reviewing a movie,if He says it is a bad movie,do I not go and see it...NO!I use My Own Judgement and You should do the same.
Rachel Y.
Reviewed in the United States on June 1, 2012
After reading the reviews on this stuff I was hesitant to buy. This is of course a sticky product, as are most products of this type due to the chemical composition. As per the directions I wore gloves, unlike most of the other reviewers it seems. I did drip some of this stuff, but if you have a throw away towel handy to catch the drips you should be fine. Also, nail polish remover gets this stuff off of whatever you drip it on as long as you are quick-acting. I wouldn't use it if a "finished" look is desired, as this stuff is an eyesore, but it serves its purpose. This is especially helpful under sinks to seal wall cut-outs for piping. It dries to a hard material and expands about 2-3 times its original application size. I would suggest testing it first outside before starting use to get comfortable with the consistency of the material and how it is released from the can. Overall a good product for its intended use.
Recommended Products
