Your cart is empty.
Your cart is empty.Product Description
Replacing faucet handles is an easy DIY project. New handles help restore faucets to "like new" condition. This Universal style diverter handle will fit any tub or shower faucet.
From the Manufacturer
Danco is one of the largest plumbing repair, replacement and remodel suppliers in the home improvement industry. We are largely focused on empowering Do It Yourself consumers with affordable plumbing products and solutions which create new and refreshing décors for bathrooms and kitchens.
Michael
Reviewed in the United States on September 12, 2024
Didn't fit. Sent back.
Mixed Coffee
Reviewed in Canada on August 12, 2024
Inaccurate description -- Not Universal -- Does Not Fit Moen Showers
Joe
Reviewed in the United States on May 21, 2024
Replaced hard to find plastic Delta large handle and it is solid.
Brittany
Reviewed in the United States on June 1, 2023
The knob on my old faucet broke and this worked perfectly. It's a little hard to turn when it's wet, but it does the job and was so easy to install.
Aret
Reviewed in Canada on February 28, 2023
Not sure this item is very universal. Grip is not good at all either
Customer
Reviewed in the United States on November 2, 2023
Easy to install and works fine. Great product for the price.
Rian Powell
Reviewed in the United States on July 25, 2022
The sizes didn't match up was to long to going out ward and not short enough for not use with stem need a wider one also but still works for the moment
Tingis Pingis
Reviewed in the United States on February 24, 2022
This product came with everything necessary to install the knob except for a screwdriver, which wasn’t a problem at all. It took me about 5 minutes to install using the instructions written on the back of the box— just unscrew the old knob, replace, and screw back in. Super easy and really elevated the look of my bathroom; it doesn’t look cheap!
Ruth Ann Rickey
Reviewed in the United States on November 6, 2022
Within days of my bathroom remodel, the handle fell off my Diverter stem. The stem was too short for the handle to grip securely. So I have had vice grips on my shower Diverter stem for 7 years! I bought this despite some of the comments in reviews and am glad I did. However, it wasn’t after a challenge. The canopy was too deep (new handle was too long). After no luck to find a replacement that would fit (even though they said universal) I thought to trim the edge to shorten it. So I carefully cut about 3/4 to an inch off the open end with a hacksaw, then smoothed the trimmed edge with a sander. Voila! My shower now has a handle like a normal person. It works great!
Client d'
Reviewed in Canada on November 1, 2022
Great product
Anik Laface
Reviewed in Canada on January 9, 2021
Not universal, it's in the trash now as it didn't want to setup.
D, Charleston SC
Reviewed in the United States on October 7, 2020
The original (unknown manufacturer) handles were not comfortable in hand, but the spline on the valve stem was impossible to match with any replacements after searches in the usual home improvement stores and online.The clamping 'vise' adapter included, solved this problem nicely.The finagling was as follows:The end of the original valve stems did not extend past the trim tube that conceals the stem. This presented a problem in that the screws to tighten the 'vise' adaptor were not accessible when placed on the splined end of the valve stem.This was remedied by unscrewing the trim tubes.... then installing the 'vise' adapter... then reinstalling the trim tube.When it comes time to attach the knob to the stem you must align the notches on the 'vise' adapter to the insideof the knob.Then install the knob keeper screw.I had to use the long spacer that is included to keep the knobs from touching the shower wall.In order to get the long spacer (if used) aligned properly to the 'vise' clamp and the knob, insert the proper long keeper screw into the knob and spacer with the spacer aligned inside the knob.Then align the other end of the spacer to the 'vice' slots, and then tighten the knob keeper screw.There is only the one spacer included, so the instruction to choose the best spacer make no sense.If the spacer length is too long, I think cutting it down to size with a hack saw would work, but the he length of knob keeper screw would have to be shortened also.There are 3 different style long keeper screws included to use if the long spacer is used. They are each a different thread pitch, so test to see which one is correct before installing the knob and tightening.
Recommended Products
