Your cart is empty.
Your cart is empty.Product Description
Package Included DC 24V Extruder Hot End Fan and DC 24V Turbo fan.Fit for Creality Ender 3, Ender 3X, Ender 3 Pro.
DC 24V Extruder Hot End Fan and Turbo fan
Strong Wind Force and Low Power Consumption.
Fit for: Creality Ender 3, Ender 3X, Ender 3 Pro
Size
About 40x40x10mm / 1.7x1.7x0.39 inch;
Package Included
2x DC 24V Extruder Hot End Fan 2x DC 24V Turbo fan
Ben
Reviewed in the United States on March 5, 2025
A lot quieter that the one that came with it
ALAN 81
Reviewed in the United Kingdom on January 5, 2025
Bought this for my Ender 3 Pro Max as both fans stopped working, both worked perfectly now. Had to attached one of the fans with the original wiring which meant cutting it and connecting it to the end of the original wire (wasn't hard to do) but the other fan was a simple straight swap out.
Francesco Rachieli
Reviewed in Italy on January 12, 2025
Un plag and play perfetto
Ashton davis
Reviewed in the United States on August 12, 2024
It works, holding temp where it should (v3 KE) I didn't even know it started to cool LOL, had to use a flashlight to verify. 10x quieter than the OE fan ever was. I hope this one lasts!
Kenneth c.
Reviewed in the United States on May 24, 2024
I was cleaning out my hot end and accidentally put a screwdriver through the original fan while it was on while switching the fan from one hand to the other. Bonehead mistake, I know. I bought this to replace it, and it's as good as new. They give you a long enough lead to wire it into the board without issue. I opted not to do that because the manufacturer of my printer hot glued the leads for the old fan into the board, and I didn't want to deal with that. So, cut the leads and soldered the wires together just above the hot end. It's not pretty, but it works. Installation was kind of a pain, but that's because of the printer manufacturer, not the fan manufacturer. This is a great product and I couldn't be happier with it.
Customer
Reviewed in the United States on December 31, 2024
The main cooling fan, that runs continuously was getting noisy, and seemed to be slowing down. This replacement, fit perfectly, and it has run quietly ever since. Watched a few youtube videos CHEP I think it was, to know how to cut the wires properly.
Trevor Becker
Reviewed in the United States on November 19, 2024
I had a major clog that ruined a lot of pieces and started swapping each part one by one. This was easy to replace and works just as good as the original. No problems so far
Customer
Reviewed in the United States on January 11, 2024
Bought BC accidently put an Allen key through my stock hot end fan. New one seemed good but I had nothing to directly compare it to. But what I can speak on is the blower fan. Since I put it in a dual part cooler setup with my stock blower fan. This blower fan is about moves about 25 to 30% more air than the stock blower. Its noticeable just by putting your hand near it. Its also visible in my prints. The one side of my prints with overhangs visibly look better on the side that this blower is on. Also at lower speeds under 10 percent this fan is slowly pushing air while my stock fan is just twitching. They are wired together in paralell so I know they are seeing the same voltage. Big win on these lil blower fans they are really good. I'm back for another set.
Alejandra vargas
Reviewed in Mexico on April 7, 2024
Funciona exactamente como el ventilador de fabrica que ya venia
Judge
Reviewed in Germany on April 6, 2024
I didnt know Comgrow sells creality parts. Well I dont know how they do it but the things I bought from them (not just the fans) seem better than the original.
Cole
Reviewed in Canada on December 15, 2023
Works great and was the exact same fan as the one pre-installed on my Ender 3v2. Did have to snip the wires of the old fan and solder them to this one, but it didn't take very long.
Saundra Wright
Reviewed in the United States on August 27, 2022
You can either buy wires with the connector on the end to go with this or splice the wires by hand. The product itself is fine, but not an instant install.
Felix del Gato
Reviewed in the United States on December 11, 2022
Jeez... So much more quiet after the stock fans on the Voxelab Aquila? The again, another reason it's $100 cheaper than Ender.Don't get me wrong. I love my Aquila. Great first printer. But, fans aren't great. Already had to replace PS fan. It got really noisy. The part cooling fan would sceetch on power up but after maybe 30-45 seconds it would settle down and work fine. Finally got tired of it and decided to swap out. This was a good deal and...really long the long cables....no soldering. Since I figured I'd need to swap the hot end fan eventually so... I swapped them both out.I used to be able to hear the printer just idling... reminding me to shut it down. Now... I can't hear it unless I'm in the bedroom converted to printing shop and the hanger. Got a bunch of RC planes hanging in the wall in there...lolSo yea, I've only had them installed for a few days but I print a lot! Time will tell as to how they stand up after the punishment I put them through.As far as the Aquila...I think it's and excellent first printer. You'll want to do some upgrades. The Alex firmware, auto bed leveler and... flexible bed... drawing a blank...PEI bed?,I've also upgraded hotend for higher temps and Bowden tube but.. you'll end up upgrading most of these for entry level Ender anyway.
Recommended Products