Your cart is empty.
Your cart is empty.
42-40 motor for e-axis of Creality Ender and CR series printer,
such as Ender3 / 3pro / 5 / 5pro / 5plus; CR10 / 10MINI / 10SProV2 / 10S4 / 10S5 / 10MAX / 10V2 / 10V3;
The 42-40 motor also fits Ender5 / 5pro / CR-10 V2 / CR-10S Pro V2 Y axis.
Material: metal.
Step angle: 1.8 degrees
Phase 2
Holding Torque: 0.4N.M
Rated current: 1A.
Shaft diameter: 5 mm, D-shaped
Frame size: 42 x 42 x 40 mm/1.7 x 1.7 x 1.6 inches.
Item weight: 290 g
Package list:
1 x 42-40 stepper motor.
georges hossann
Reviewed in France on February 18, 2025
Mon imprimante 3 d a repris goût à la vie
Stacy
Reviewed in the United States on August 31, 2024
If you’re here, you probably realized you need a stepper motor with a flat sided shaft. This is it, at least for the OG Ender 3. Just get it, it’s worth it compared to trying to replace the press-fit gear and grinding a side into the rod of the original stepper motor. Take it from someone who tried to do it that way. It’s only like $15, just buy it. It saved me a bit of headache (compared to the machine itself). Plus, now that your rod is longer, you can put a little knob on it! Hehe
Theodore Arensmeier
Reviewed in the United States on August 15, 2024
I actually just got this because I couldn’t get the feeder gear off the original one on the printer when I was trying to replace it. This swapped in and has now has several dozen hours on it. Printer is a Creality Ender 3 v2.
Alasdair
Reviewed in the United Kingdom on July 16, 2024
Bought to replace a z-axis motor that was getting a bit too hot on long prints. This motor runs warm but substantially cooler than the previous one, making me much less worried about 'magic smoke'...!
Rudi rdv
Reviewed in Belgium on June 28, 2024
Werk goed en doe wat hij moet doen
Verified buyer
Reviewed in the United States on June 20, 2024
I used it for my extruder since the stock motor shaft wasn't long enough. It fit and worked great.
EN
Reviewed in the United States on June 15, 2024
I used this to replace a motor on my Sovol SV03 which axis broke. Seamless replacement. Printer works as before. Same fixation points, no calibration of any kind. Just switch and go.
Louis suberville
Reviewed in Mexico on February 9, 2024
Hace años lo compré y sigue sin detenerse por horas y horas. El que reemplazó dejó de servir por qué lo abrí, manos de estómago me dicen.
Raul
Reviewed in Spain on December 2, 2024
Perfecto para mí Ender 3 , lo compré por qué se rompió el mío y completamente idéntico al que viene con la impresora
Professional Generalist
Reviewed in the United States on May 24, 2023
When I get a new printer, I remove the extruder stepper and replace with this because this has an extra long shaft to attach a turnwheel so that you can manually prime the extruder. Love these guys.
Casey barney
Reviewed in the United States on December 2, 2023
I needed a longer shaft on my ender 3 this was to allow for a updated duel drive extruder. It plugged in and mounted up good. It works way better then stock.
shadetree
Reviewed in the United States on October 19, 2023
The stock Creality extruders have a short motor shaft with the pressed-on gear. They won't work with the Micro Swiss direct drive extruder or with a dual-geared extruder. This stepper has a longer shaft and a flat spot for the grub screws.
Brian Florido
Reviewed in the United States on February 23, 2022
So I have an original gen1 ender 3 which turned out to having a shorter shaft and a press fit gear. After removing the press fit, found that the shaft of the motor was too short for the upgrade I was performing. all and all, there was more work to getting extenders and couplings than it was worth. so If you are going to upgrade, this is it. don't cheap out, this will save you a lot of time and headache. somethings are just worth getting and this is it.
Recommended Products
$79.99
$ 35 .99 $35.99
$25.08
$ 12 .99 $12.99