Your cart is empty.
Your cart is empty. Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a Dry environment.
Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 3/4".
Length Anchor
The length of the anchor is 7"
Thread Length
The length of the threads on the anchor is 4" in length.
Minimum Embedment
The minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.
Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3". This will ensure that the minimum embedment of 3-1/4" will be met.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.
Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.
Edge Distance
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.
Customer
Reviewed in the United States on February 23, 2025
These are awesome! Use them at work and home. My 2 post lift will never move with these holding it down. 💯
Steven Crowder
Reviewed in the United States on February 22, 2025
Worked for my application. No issues installing and have held for over a year now
AMR
Reviewed in the United States on January 20, 2025
Use these all the time anchoring posts into concrete, always work great without slipping in concrete.
Customer
Reviewed in the United States on August 31, 2024
The anchor's sleeve doesn't engage immediately and results in the bolt engaging toward the top of the hole. The best I could do was to drill deeper and carefully insert the bolt so that the nut would engage and start tightening until the wedge engage. Then back the nut off and place what I was anchoring back over the bolt with the washer and nut and then torqued it.
Customer
Reviewed in Canada on July 26, 2024
Used to install my car hoist works great!
cal
Reviewed in the United States on December 14, 2024
used to hold down car lift......my life is on the line.......good product
R.D.
Reviewed in the United States on November 4, 2024
Quality name not generic and does the job. Very happy with purchase and would buy again.
Maria N. Barnes
Reviewed in the United States on October 27, 2024
I used these bolts on a two post lift in my shop. They worked great and I torqued them to 175 lbs. no issues at all.
Stepside66
Reviewed in the United States on April 16, 2024
Used 12 of these in a 2-post lift install. These things are awesome and very robust. Installed all 12 without a problem. Torqued all to 150ft lbs. after 1 week, I retorqued them all and all but 1 retorqued to 150ft lbs with less than 1/2 turn. One pulled almost all the way out. So, I hammered it back through and installed a new one and it torqued with less travel than the failed one. Faulty anchor? Faulty concrete? All good now.
ben64
Reviewed in Canada on February 1, 2023
They did the job and were a great price compared to others.I had some that bit hard and torqued down nicely. Others that took a while to bite and get a decent torque. Used to set up my 2 post hoist. End of the day they held down the hoist when lifting a 9000lb truck.
Maureen Ernst
Reviewed in Canada on December 8, 2023
Went in good to hold new car hoist down hope it stays strong
Grant Killeen
Reviewed in Canada on December 7, 2023
Solid product. Perfect for mounting light posts
Recommended Products
$29.80
$ 13 .99 $13.99