Your cart is empty.
Your cart is empty.Product Description
Filiep Samyn
Reviewed in the United States on February 23, 2024
Advertised as 14.0 mm bore but it measures 13.9 mm; hence it doesn’t fit. How can QA not catch this.
M. Houston
Reviewed in Germany on February 20, 2024
I purchased these to extend my bench press table lift to the front of an extension table. Solidly constructed and fit perfectly on the shaft I was using. Highly recommend!
Mike Someone
Reviewed in the United States on July 15, 2023
These are very well made and durable. A small amount of filing the key way to fit was all that was needed. These should last forever.
Alessio
Reviewed in Italy on June 16, 2023
Buon materiale non male
Stjepan Mijatovic
Reviewed in Germany on March 8, 2023
weiter so
Woodman5
Reviewed in the United States on January 25, 2023
Gears matched well.
Customer
Reviewed in the United Kingdom on October 5, 2022
As above they are just what I wanted
mrbean
Reviewed in the United States on August 19, 2021
My original intent was to use this for a new table that I made for my Delta 11-990 drill press. (see enclosed picture). The new table was encroaching on the handle (note handle is normally located next to the drill press post) that I used to lower or raise the drill press table. As a result I couldn't turn the handle completely. The strategy was to relocate the handle to the front of the drill press table so it would be out of the way. I saw several You Tube videos on how to do this. To do that I needed these mesh gears to change the direction of the shaft by 90 degrees. When I tried doing this I encountered what appeared to be a lot of resistance. I concluded that changing the direction by 90 degrees did add a fair amount of resistance. So, in the end I didn't use the mesh gears. In the enclosed picture, I simply extended the shaft further to the right edge of the drill press table and accomplished the same thing. By not changing the direction of the shaft, I was able to turn the shaft pretty easily to lower or raise the table. The gears accommodated a 14 mm shaft, and that was pretty accurate. My shaft was 1/2 inch (obtained from Lowes), so that was a little smaller than the 14 mm internal diameter of the mesh gears. In addition, these mesh gears have a slot for a key, so for my purposes, the set screws that came with the mesh gears (which would press down on the key) were too short (since I had no key and since the set screw had to reach the 1/2" axle. I had to go to a local hardware store to get longer M5 set screws. I'm not going to return these mesh gears but will save them for a possible future project. It would be best to use a 14 mm shaft ( I used the 1/2" shaft from Lowes since it was a lot cheaper and a lot longer). Be aware that these mesh gears are made to accommodate a key. (key does not come with the gears). I used 2 layers of gorilla tape wrapped around the 1/2" shaft to better center the shaft in the handle and also the 14 mm coupler shown in the picture.
Arthur Buchanan
Reviewed in the United States on February 1, 2021
Good quality worth the price
Larry M
Reviewed in the United States on January 25, 2021
As others have mentioned, they could be polished to a better finish, but then the price would reflect that. I think that beveling the outside edge of each gear face will smooth them out considerably. Some won't mind doing this but others might not want to put in the effort. Overall, I'm satisfied with them.
Logan benoit
Reviewed in the United States on April 28, 2021
I use these gears to make a drill press upgrade. They work perfect.
Mr. Dextrose
Reviewed in the United States on January 9, 2020
I bought these for a project in my wood shop. I expected them to be sintered metal powder but it turns out they're actually machined from stock. The precision of the bore, gear cut and key way are good but the teeth are a bit rough. This gear set would work fine in low speed or intermittent applications such as mine.
coumichri
Reviewed in France on December 9, 2019
livrés rapidement, aussitôt montés en dépannage, tout fonctionne,nous sommes très satisfait.
Recommended Products
$14.83
$ 7 .99 $7.99