Your cart is empty.
Your cart is empty.Product Description
Replaces P/N: 5912561, 5912496, 164-R8056
For FCC ID: CWTWB1U793
For IC/Other: 1788A-FWB1U793
Remote Programming: Self programmable with one working key
Key Programming: Self programmable with two (2) working ORIGINAL master keys
*NOTE: Will not work if vehicle ignition currently has an ignition guard*
Alberto
Reviewed in Mexico on February 25, 2025
gran material ,cumple con la descripción.
TheDude
Reviewed in the United States on January 24, 2025
It worked as described, however for my 2011 f150 lariat with remote start, I had to use forscan to program the ignitionchip part first to be able to start the vehicle, but buttons did not work thats when I used the instructions that came with the controller for the buttons to work, it's weird but that's how I got mine to work flawlessly. By the way it's a pain in the ass to find someone that will cut them, luckily an ace hardware made me 2 copies,
William
Reviewed in the United States on May 2, 2024
Programming the key was easier than getting the key cut. ACE hardware could not get the grooves deep enough on their manual machine. After 3 attempts I left with a paper weight, per se. Went to local hardware store and they didn't want to do it but I told them it was currently worthless and they couldn't screw it up any worse. They took a shot and it worked and they didn't charge me, so I got the key cut for free. 11 minutes and key was programmed and could manually lock/unlock my 2014 F150 but FOB didn't work. I looked on YouTube and found how to program a fob. You can use any working ket and cycle the Ignition 8 times, can't be too fast or too slow. The door locks will cycle and then you push the lock or unlock button (on the new fob and doesn't matter which button you push) you'll hear the locks cycle then you'll turn the key to the off position and locks will cycle again. Remove the key and try your new key fob and it should work.
Mrs. Laban
Reviewed in the United States on November 20, 2024
Zero stars. Although the product description informs that fob must be programmed by a dealer, the item itself does not comport to Ford proprietary programming software. So, in addition to wasting $19.95 on the item, I paid $79.95 at the dealer only to find it is not compatible with Ford software. Yes, you can cut the key to fit your doors, and it can be programmed to run the peripherals. So if you just want to sit in your car and listen to music with the air on, that’s fine, but if you want to actually drive the vehicle, this product does not have the correct electronic chip to accept the programming. If you still want to try it after reading this, make sure you get it to the dealer within 30 days of purchase or, like me, you won’t even be able to return it. *Buried somewhere in the listing, it does say it will not program if the vehicle has an “ignition guard” but it is my understanding that all newer vehicle have an ignition guard as part of the vehicle protection. My Ford is 13 years old and must have an ignition guard, so how old must a vehicle be to not have it?
Shawn
Reviewed in Canada on November 10, 2024
This is OE quality and as described blank key and fob ready for key cut and fob programming
mubashir ali
Reviewed in Canada on August 2, 2023
I got these keys because I only had one key. When they got here I was thrilled but when I took it to the dealership to get them cut and programmed we ran into a problem. The dealer successfully cut the keys but said that the buttons could not be programmed because the chip is defective. A refund would be appreciated and a return won’t work since the keys are already cut.
Juan Carlos Ruiz Morales
Reviewed in Mexico on June 2, 2023
Solo sirvió un mes, después lo tuve que tirar.
María Dolores
Reviewed in Mexico on February 7, 2022
Un muy buen producto estoy satisfecha con la compra funciona muy bien.
Cenla Cathy
Reviewed in the United States on September 9, 2018
My Sport Trac had a key and then a separate fob to open the doors. I wanted to have fewer items on my keychain and this key helped. I was able to easily program the key to start the truck, and then (separate steps) also program the key to lock/unlock the doors. Steps for both tasks are below. The key works perfectly, and I'm happy that I was able to able to do the programming myself rather than paying big bucks to the dealership.For a 2007 Ford Sport Trac XLT:To program the key to start the truck:1. You must have 2 keys that are already coded to start the truck.2. Take one of the already coded keys and put it in the ignition.3. Turn it to position 3 for at least 3 seconds, but less than 10 seconds.4. Within 10 seconds, take the 1st key out of the ignition and put the second pre-coded key in.5. Turn it to position 3 for at least 3 seconds, but less than 10 seconds.6. Within 10 seconds, take the 2nd key out of the ignition and put this new, uncoded key in.7. Turn it to position 3 for at least 3 seconds, but less than 10 seconds, then take it out of the ignition.You should now be able to start the truck with any of the 3 keys.At this point, I was able to start the truck, but the key did not lock/unlock the doors. I had to also do the following to make the key lock/unlock the doors.To program the key to lock/unlock the doors:VERY IMPORTANT: ****You must have ALL the remotes that you want to be able to use to lock/unlock the doors available for this process. Any remotes that are not involved in this process will no longer work.****1. With all remote devices in hand, close all the doors to the truck.2. Use one of the remotes and press the UNLOCK button.3. Insert a coded key into the ignition.4. VERY QUICKLY, turn the key to position 3, back to 1, back to 3, etc. 8 times. Finish with the key in position 3. You must complete this within 10 seconds.5. After the key has cycled to position 3 the 8th time, the doors will lock and unlock to confirm programming mode has been engaged. (the first couple times I did this I wasn’t cycling between OFF and position 3 fast enough, so the doors didn’t lock/unlock)6. Within 20 seconds, push any button on one of the remotes (such as this key). The doors will lock and unlock to confirm the remote is programmed.7. Within 20 seconds, push any button on the second remote. The doors will lock and unlock to confirm the remote is programmed.8. You can repeat this for a total of up to 6 remotes.9. When done, turn the key in the ignition to OFF. The doors will lock and unlock to confirm programming mode has ended.At this point, my new key both started the truck and would lock/unlock the doors.
Recommended Products
$28.22
$ 13 .99 $13.99