Shopping Cart

Your cart is empty.

Your cart is empty.

Byrna 12 Gram CO2 + Oiler Cartridges | 10 Count Pack | for Byrna LE/HDXL/SDXL and TCR - (9 CO2 + 1 Oiler Cylinders)

4.3 (8) Write Review
Free shipping on orders over $29.99

$19.99

$ 8 .99 $8.99

In Stock

About this item

  • WHAT'S IN THE BOX: (10 ct.) 12g CO2 Cartridges. Including 9 standard 12g CO2 cartridges and 1 CO2 cartridge including oil for maintenance.
  • EASY TO USE: Simply install the oiler cartridge like any other 12g CO2 cartridge and fire away! The CO2 with Oil cartridge does all the work while you fire.
  • COMPATIBILITY: Byrna 12g CO2 cartridges are custom fit for the Byrna TCR / LE / SDXL / HDXL or launchers with the Byrna boost 12g adaptor installed.
  • PLEASE NOTE: This pack of CO2 cartridges includes one marked cartridge that contains CO2 + Oil. We recommended using this CO2 + Oil cartridge every 5th cartridge to maintain lubrication and optimal performance. The oil cartridge is not always labeled and is placed in the box facing the opposite direction as the other 9 cylinders. The oiler cartridge can be used just the same as the other CO2 cartridges
  • Not compatible with Byrna SD, EP, or HD models.


Product Description

Byrna
Byrna
Byrna
Byrna
Byrna

co2

Note: The cap will require very little pressure from the tool and should spin with little to no resistance. Continue turning until you begin to feel resistance against the CO2 Cartridge. From this point, continue tightening 1/4 turn further.

Do not over tighten the cap.

  • While the CO2 cartridge will be enough to power 20+ rounds, once the CO2 is pierced, even if it is not fully exhausted, it should be replaced by an unused cartridge before the launcher is stored.

HOW TO INSTALL YOUR NEW LAUNCHER’S CO2 CAP?

  1. Put the launcher in SAFE mode (if equipped with a safety), remove the magazine and make sure there is not a projectile in the breech.
  2. Point the barrel in a safe direction. Remove the CO2 cap using the cap tool (built into magazine base).
  3. Insert a new unused CO2 cylinder into the CO2 chamber and use your finger to push the cylinder firmly to the back of the chamber.
  4. Begin threading the CO2 cap by hand to prevent cross-threading.
  5. Use the CO2 cap tool to continue tightening the cap.
  • It is recommended to keep an unpunctured cylinder in your launcher at all times for self-defense purposes. Punctured cylinders within your Byrna Launcher will leak over time.

Jesse Powell
Reviewed in the United States on February 19, 2025
These work good in my Byrna.
jerry
Reviewed in the United States on February 16, 2025
Works well thanks
Dennis Brumfield
Reviewed in the United States on February 15, 2025
Just what I needed
Kenneth L Shelton
Reviewed in the United States on January 9, 2025
They don't necessarily sing like the band but they do work as they are supposed to. They send my projectiles down range at a very high velocity which is what is necessary to have some fun. I also appreciate that they give me an oil cartridge for gun maintenance.
John May
Reviewed in the United States on December 10, 2024
Byrna launcher
kevin shannon
Reviewed in the United States on November 25, 2024
I'M AN AVID PISTOL/RIFLE (DID SOME SNIPING IN VIETNAM WITH M-2 50 CAL GUNS) SHOOTER AND I RECOMMEND A LONGER BARREL- SAY ANOTHER 2 INCHES, I'VE FIRED MINE AT VARIOUS AND THE POWER IS TH SAME NOMATTER THE RANGE- NOW FACT OF SHOOTING GUNS IS 1. LONGER THE BARREL THE LONGER THE RANGE AND INCREASED ACCURACY WITH THAT EXTRA 2 INCH BARREL. APPLIES TO ALL GUNS; PISTOLS RIFLES CANNON ESPECIALLY TANK CANNON- ALL SUCCESSFUL TANK GUNS HAD LONGER BARRELS AND INCREASED PUNCHING POWER AGAINST OTHER TANKS..
ron allsop
Reviewed in the United States on November 17, 2024
nice
Mike M
Reviewed in the United States on November 15, 2024
These CO2 cartridges are exactly what I needed for my Byrna gun. They work perfectly, delivering consistent power with each use, and are easy to install. Great quality and reliable – I'll definitely be purchasing these again! They are very costly.