Your cart is empty.
Your cart is empty.Product Description
About Taps
Straight flute design, made of 6542 high speed steel. It is used to process threads of various through holes or shallow blind holes. Can process copper, brass, A3 steel, aluminum, cast iron and other materials.
Generally used in conjunction with tapping machines, integrated bench drills, CNC lathes, machining centers, etc. Manual processing is also possible. When operating, control the speed according to the hardness of the material, the higher the hardness of the processed product, the slower the speed.
Recommended feed rate:
Hard steel: 5-10m/min, cast iron: 8-10m/min, ordinary steel: 6-15m/min.
About Dies
Made of alloy tool steel, hardness and wear resistance. Used to repair external threads. When in use, the conical locking hole of the die is aligned with the screw of the wrench and tightened. The conical keyhole has a strong locking force and is not easy to loosen.
Suggest:
Appropriate lubricating oil should be added to the die-cutting edge when cutting, It is to be reversed every 1/4~1/2 turn to facilitate chip discharge from the chip hole.
KAREEM
Reviewed in Saudi Arabia on January 10, 2025
Required two kits .otherwise get only one . And you when useed is broken
DenisR
Reviewed in the United States on September 1, 2024
The RCA style jack has a 1/4 x 32 threaded mounting stud, see pic. I needed to mount an RCA jack to a 3/4" wood base. I used an E-Z LOK Knife Threaded Insert with a 1/4 x 20 internal thread. I re-threaded the insert with the 1/4 x 32 tap and screwed the RCA jack into it. The new thread is not perfect but it provides a lot of strength, strong enough that it can't be pulled out of the E-Z LOC even using pliers. Using an RA solder flux I soldered a wire to the end of the E-Z LOK insert for the ground connection, it soldered very well.
Ron
Reviewed in the United States on August 21, 2024
Worked perfect for its intended purpose.
Joey Welt
Reviewed in the United States on July 17, 2024
This is a huge lifesaver for cleaning up the threads and holes for vintage appliances, in my case a 1930's Hamilton Beach drink/milkshake mixer. These vintage appliances are notorious for cross threading due to zero give, a quick cleanup of the screws will save you dozens of angry hours later!
Marco Pruscini
Reviewed in Germany on July 15, 2024
Gute Qualität
Ingvar Nilsson
Reviewed in Sweden on June 10, 2024
This thread is not uncommon in fine machanics and can be found in both American objects as well in Brittish . However when getting this set for 1/3 of lowest price I've found I can cope with the limitation in cutting performance. The major issue is that the tap requires quite high torque to cut the thread. The die cuts with normal torque. I give my top rating.
Jay B. Sigel
Reviewed in the United States on May 13, 2024
Every tap and die kit I have ever owned, and I have at least 4, has had 1" dies - except this one. I had hoped that since the product description has NO MENTION that it's 20 mm in diameter, that it would be the standard 1"/25 mm die diameter. Wrong! I have no handle that will fit this thing. Now, I have to look for one and hope that it will properly fit. Meanwhile, I can't use this die.
Karl R.
Reviewed in the United States on December 16, 2024
Item was as described.
Frank
Reviewed in Germany on November 13, 2024
Scheint eine gute Qualität zu haben. Eine fundierte Aussage kann man erst nach längeren Gebrauch machen
Craig Butler
Reviewed in the United States on October 31, 2024
Die was too small for the holding tool
OverACliff
Reviewed in the United States on October 19, 2024
Used the tap on aluminum. Works. Would recommend.
Bob St Amand
Reviewed in Canada on February 18, 2023
This is a rarer tap size as it is for a 1976 Harley Tappet block that had messed up thread. I got the tap and die day after order and was able to clean up the messed up threads. It is a good quality for price given that I won't be using everyday. Very satisfied with this tool
PA&PJ
Reviewed in the United States on April 20, 2023
Making small screws with fine threads is difficult and if you only need one or two it costs more tobuy them including shipping so the cost of the tap and die is well worth it!
Recommended Products
$43.99
$ 19 .99 $19.99
$26.99
$ 12 .99 $12.99