Shopping Cart

Your cart is empty.

Your cart is empty.

Black C-Clamp Cantilever Bracket Clamp Holder Desk Lamp Clip Fittings Base Hose DIY Swing Arm Lighting Accessory Metal Clamp

Free shipping on orders over $29.99

$8.59

$ 3 .99 $3.99

In Stock

About this item

  • Package included: 1 x Black C-Clamp.
  • You can securely install your microphone and desk lamp bracket on a desktop or other flat surface by adjusting the positioning screws.
  • Applicable size: Easily clamp a table top with a thickness of 2.24 inches / 5.7 cm; the hole diameter is 0.47 inches / 12mm.
  • The contact side of the table is protected by a soft rubber pad to prevent your table from being scratched.
  • The installation is simple and convenient, without any tools, suitable for all kinds of swing arm lamps, magnifying lamps, desk lamps, microphone holders, and mobile phone holders that meet the installation aperture (less than 12mm).


Package contains: Black C clip*1

Advantages: the thickened clamp will not be deformed when tightened forcefully, easy to install, no tools required.

Suitable for all kinds of swing arm lamps, magnifying lamps, desk lamps, microphone holders, mobile phone holders, etc. that meet the installation aperture (less than 12mm).


Bill Karoly
Reviewed in the United States on February 9, 2025
I love this. It's a solid metal replacement for the plastic part that fell apart.
Bill Karoly
Reviewed in the United States on February 9, 2025
I love this. It's a solid metal replacement for the plastic part that fell apart.
Jason Delaney
Reviewed in the United States on September 5, 2024
Works Great
Jason Delaney
Reviewed in the United States on September 5, 2024
Works Great
IzaTomek
Reviewed in the United States on September 27, 2024
For light duty maybe, but on the work bench it’s cheap pot metal. A good hard tighten and it cracks
IzaTomek
Reviewed in the United States on September 27, 2024
For light duty maybe, but on the work bench it’s cheap pot metal. A good hard tighten and it cracks
Kemo Sabe
Reviewed in the United States on September 18, 2024
Worked fine, allowing me to resurrect a clamp-on desk lamp I hadn’t been able to use for quite some time. Fit the ½” stem of the lamp perfectly.
Kemo Sabe
Reviewed in the United States on September 18, 2024
Worked fine, allowing me to resurrect a clamp-on desk lamp I hadn’t been able to use for quite some time. Fit the ½” stem of the lamp perfectly.
Eduardo Mestre
Reviewed in the United States on June 27, 2024
The bottom press does not have anything to cushion the pressure, so it can damage your table underneath.
Eduardo Mestre
Reviewed in the United States on June 27, 2024
The bottom press does not have anything to cushion the pressure, so it can damage your table underneath.
BrickPig
Reviewed in the United States on February 9, 2024
I bought this 12mm desk clamp to replace the flimsy weighted plastic base that came with my lighted magnifying lamphttps://www.amazon.com/dp/B0CPLZCPS7?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe 12mm socket of this desk clamp works perfectly with the lamp. The clamp is sturdy and the lamp no longer wobbles. I got this clamp because of the minimal footprint and low cost. I wish the silver lever to tighten the clamp was a bit thicker, however I suppose that will also prevent too much pressure being applied by the screw clamp. Great value and recommended!
BrickPig
Reviewed in the United States on February 9, 2024
I bought this 12mm desk clamp to replace the flimsy weighted plastic base that came with my lighted magnifying lamphttps://www.amazon.com/dp/B0CPLZCPS7?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe 12mm socket of this desk clamp works perfectly with the lamp. The clamp is sturdy and the lamp no longer wobbles. I got this clamp because of the minimal footprint and low cost. I wish the silver lever to tighten the clamp was a bit thicker, however I suppose that will also prevent too much pressure being applied by the screw clamp. Great value and recommended!
J. Michael Johnson
Reviewed in the United States on October 10, 2024
It did not fit my project but perfectly serviceable for something else. If you plan on inserting something in the round hole at the top, be sure to measure the diameter of the hole precisely. I was off by a fraction and couldn’t use it for my intended project. But something else will come along.
J. Michael Johnson
Reviewed in the United States on October 10, 2024
It did not fit my project but perfectly serviceable for something else. If you plan on inserting something in the round hole at the top, be sure to measure the diameter of the hole precisely. I was off by a fraction and couldn’t use it for my intended project. But something else will come along.
Customer
Reviewed in the United States on November 29, 2023
This clamp holds my lamp very well no wiggling
Customer
Reviewed in the United States on November 29, 2023
This clamp holds my lamp very well no wiggling
Recommended Products