Shopping Cart

Your cart is empty.

Your cart is empty.

BIGTREETECH Upgrade PI TFT43 TFT LCD Display DSI 800x480 for Raspberry Pi Model 3D Printer Controller(3in Capacitive Touch Screen) (105.5X67mm)

Free shipping on orders over $29.99

$52.99

$ 27 .99 $27.99

In Stock

1.Size:Pi Tft50


About this item

  • Wide Range of Applications: 5 inch capacitive Touch Screen designed for for pi 4 model B /pi 3 model A+ B+ B/pi 2 model B/pi 1 model B+ A+
  • High Resolution: This 5 inch LCD touch screen with a resolution of 800*480 and a display area of 108x64.8mm
  • 5-point Touch: It Supports Raspberry Pi DSI display interface, comes with a capacitive touch panel, and supports 5-point touch.Capacitive Touch Control ,better touch response,faster response time
  • Easy to install: The unique hole design on the back allows you to install the Raspberry Pi directly.The display adopts Raspberry Pi power supply design, without external power supply
  • KlipperScreen Upgrade: Pi TFT50 can be paired with a host (such as Raspberry Pi 4B to run klipperscreen,which brings a seamless touch experience to your klippered printer.



Product Description

PI TFT43/50/70 V2.0 For Raspberry Pi
The Package

Screen features

  • The backlight can be adjusted by a rotary encoder, which is convenient and quick;
  • On-board studs and positioning posts can fix the Raspberry Pi, which is more integrated;
  • Use a FPC cable to connect the screen to the Pi's DSI interface, and the display can be touched, which is simple and convenient.

Screen parameters

  • Power input: DC 3.3V
  • Working method: DSI
  • Screen resolution: 800*480

Supporting single touch for Raspberry Pi system

Capacitive touch,Touch sensitive , Supporting single touch for Raspberry Pi system

Support five points touch

Support Raspberry Pi DSI display interface ,Responsive touch control,Support five points touch,easy to use ,Respond faster

This PI screen supports 180°flip of the image

This PI screen supports 180°flip of the image, one key rotation of the display direction function, and the display direction can be rotated 180°with a touch. Screen resolution is 800x480

The backlight can be adjusted by a rotary encoder, which is convenient and quick

The backlight can be adjusted by a rotary encoder, which is convenient and quick

Attention

  • Pay attention to the DSI interface line sequence not to be reversed;
  • Take care to handle the screen gently to prevent it from being broken;
  • When adjusting the backlight, pay attention to the strength of the rotary encoder to prevent it from turning bad. When the encoder is turned to the end, it cannot continue to turn, otherwise the encoder will be damaged, and our company will not accept it;
  • The screen does not support the zero version of raspberry pi

What other surprises?

  • Super easy to get up and running, very responsive
  • Love that it's powered directly from the pi via the ribbon cable! No extra wires get in the way.
  • The printer dashboard UI screen is bright and clear in color

Orlando Prieto
Reviewed in the United States on July 2, 2024
I recently purchased the BIGTREETECH Upgrade PI TFT70 TFT LCD Display for use with my Raspberry Pi 4 Model B and OctoDash, and overall, I'm quite pleased with it.The display itself is fantastic—bright, responsive, and boasting a crisp resolution that makes viewing details a pleasure. Once properly configured, it integrates seamlessly with the Raspberry Pi and enhances the user interface experience significantly."However, the setup process was not without its challenges. Upon initial installation, I encountered an issue where the touchscreen functionality didn't work at all. After spending considerable time researching online forums and troubleshooting steps, I discovered that the problem lay in the driver configuration specified in /boot/config.txt."Specifically, the display requires a particular setup that wasn't initially clear. I found that commenting out the following line was necessary to enable proper touchscreen functionality: #dtoverlay=vc4-kms-v3dOnce I made this adjustment and rebooted the Raspberry Pi, the touchscreen started working flawlessly with OctoDash
Dizzle
Reviewed in the United States on February 8, 2024
Updated my Ender-3 from Marlin to Klipper firmware. The basic LCD was not cutting it for me so I upgraded to this screen. I have a RPi4 behind it and works well with Klipper screen. This is perfect!
Ronald Arroyo-Watson
Reviewed in the United States on December 24, 2024
Display powers on backlighting is on, but Pi 5 won’t even recognize that it is connected. No files or config available to make it work on Pi 5 either.
DeltaV
Reviewed in the United States on November 29, 2024
Using this for an upgraded FlashForge Creator Pro with a SKR3 controller running Klipper and Klipper Screen.Very easy to set up with Kiauh.Search for "Add a Touchscreen to your 3D Printer - Klipper Screen - Chris's Basement"
Gerhort A.
Reviewed in the United States on November 27, 2024
Got this for my Voron 2.4 3D printer. The giant display is really nice and I have not had any issues.
Moon Dog
Reviewed in the United States on November 26, 2024
I was never much of a fan of touchscreens on printers in the past, largely because the interfaces were sub par. However Klipper Screen is pretty fantastic. I got a Voron kit that came with a 5" screen, and loved it. That is till I added the ERCF color changer. The extra screens for it were great, but a but dense. So moving up to a 7" display really made the printer and ERCF unit a joy to use. I have added these to all my Klipper based machines now. I do wish they came with a few extra screws, and a longer cable. Odds are you will need to source some alternates if you mount it any other way than with the Pi directly attached.
Matthew R
Reviewed in the United States on July 27, 2023
I bought two of these for my Voron printers. I could have gotten by with the 4.3" screen which is still pretty large but I went with the 5" on both. They mount at about a 45 degree angle and I had to use larger feet on one printer to keep it off the desk. I don't mind the angle or the elevated feet.I found some stl files for a case/mount for them and printed that. The included cable is way too short unless you plan to mount the pi to the back of the screen. (which wouldn't work for my mount) I had to order a longer cable. The packaging was nice. The little protective stickers on the screw holes were a little difficult to remove but kept dirt and things out of holes which is nice.There is a switch on the screen in case you need to change the orientation. (flip the image over) The touch aspect works great. It seems really accurate and I didn't have to do any tuning routing to get it to respond and work well. I use the screen a lot, even more than I expected to.
Kindle Customer
Reviewed in the United States on September 24, 2022
When the provided cable is connected to the Raspberry Pi 4 (tested two different ones), the screen displays nicely and the touchscreen works well. However, Wifi will no longer work on the Raspberry Pi 4.The solution provided by BTT is to get longer standoffs, but that doesn't change anything. If the cable is connected, which is required to use the display, then Wifi doesn't work. As soon as you shutdown, disconnect the cable and reboot, Wifi works again.
Recommended Products

$31.00

$ 16 .99 $16.99

5.0
Select Option