AURSINC Upgrated NanoVNA-H4 Vector Network Analyzer, Lastest V4.3 10KHz-1.5GHz HF VHF UHF 4' Touch Screen VNA Antenna Analyzer Ham Radio, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

This is very nice. I have two of the smaller nano VNAs and the narrow side of this screen is the same as the long side of the little ones.It also has a slightly different menu and it has a place for an SD chip so you can save your settings and more.This is much nicer to handle and use than the smaller ones.

Order arrived in a timely fashion. The nanovna is operation well. No issues.

I saw this in a YouTube video when I was studying for my Extra Class Licence and for the price I though I'd give it a try. Once you figure out how to use it, the NanoVNA will give you very precise measurement on your antennas, baluns and UNUNs. I used it to work the bugs out of the 49:1 UNUN I built for my 80m EFHW antenna.It has much more range than my MFJ-255C, antenna analyzer for 25% the price. (NanoVNA covers all bands from 2200m up to 23cm) It can can plot out the entire frequency range of an antenna or just look at one band at a time. The software for the PC is easy to use and gives you a bigger graphical view of what is going on. It saves the results or a screen shot to an mico SD card.Now looking at the spectrum analyzer for future addition to my shack.

Theirs is a lot of concern with these devices in general being clones. I have used this device quite a bit since purchase.The build quality and functionality of this vendor’s selling model (from wherever they get it) is legit as far as my technical use can say.I purchased some $4 screen protectors as a previous unit I had (smaller) had gotten marks from use and in reflective light, annoying. I suggest doing so.Price is reasonable.

My original NanoVNA-H4 touch screen did not function properly after working normal for a month. Menus only respond to dial inputs (not the stylus or touch). I had ordered it on Amazon, so the return window was closed (1 month). The company responded to my problem and after a recommended unsuccessful reset, sent a replacement.This is great news and I was pleasantly surprised to receive the new unit. It's good to see a company stand by their product.So far the NanoVNA-H4 is a great device for analyzing my projects.

So I had the smaller version of this - the H model without any case and after a few years it failed, so I went with the SAA-2N, but found it not as accurate and it was not upgradable by me. This is the H4 and although the print on the case is barely readable, it appears to work fine and appears to be close in accuracy to my 2 HF Antenna analyzers (MFJ 269 and RigExpert AA55).The software is updated to the latest version and works great with VNA Saver. It comes in plastic case (not metal as implied in the description). I assume the metal the description is referring to is on the board around the RF section as this case is all ABS plastic. No matter, it still seems to do what I need it to do.I am still learning to use this, but one takeaway from my previous device is make sure you discharge any outside antenna before you connect it to your device as I suspect that is what happened to my first unit - probably had static on the antenna that damaged the input of S11.The screen is easy to read and the device is fast! much faster than the SAA-2N and the H device. Haven't tested the battery operating time yet, as the longest time on battery so far has been an hour. This device is feature rich compared to the H device, so for 45 or so more dollars, a good value.

I had been sitting on the fence to acquire one of these for a long time primarily because it did not cover 1296MHz where I have and will be spending more time on antennas. A few days ago I took another look and noticed V3.4 2.8 and 4” versions released on Alibaba and now here.Yesterday I received the 4” version NanoVNA-H4. It came nicely packaged as shown in the pictures. It had a Jan 1, 2020 build date using the hugen79 branch, one of the 3 main builds I spotted so far for NanoVNA, and the one specifically developed for this new version hardware. Jan 18th a new build of firmware was released.There is a known bug that if you use a center frequency above 1GHz it may lock up. If this happens you can power cycle to return to normal. Use start and stop rather than center to work around this for now. It is already fixed in another branch’s build as of Feb 2, I suspect it will be fixed soon enough and is an easy thing to avoid.One of the concerns is what device are you buying, a clone or the real thing. Being very recently released I do not think the clones of this model have had time to show up yet, and the photos and text seemed legit so I bit. Looking at the device packaging, paperwork, PCB and the one small case clearance issue existing on my unit, it appears to match the original overseas listing and Hugen79’s own description and seems like the real thing to me. It can be hard to tell sometimes. The firmware upgrade also worked as expected. There is another build of this running in parallel but uses a different BIOS and is more targeted to developers for now but promises to expand future capabilities. BTW the “-H” designation identifies the hugen79 hardware variation from the original edy555 hardware design. The H4 is a 4” version.I ran it through several tests on a commercial 116-174Mhz 75Watt Tx filter, the SG-Labs 1296 PCB 2 element yagi, some dummy loads, various length of cables and it seems to work as expected. I also downloaded and used the NanoVNA-Saver V2.2-1 PC program (I am on Windows 10). All works well there also. The NanoSaver has a lot more real estate so separates charts with configurable sweeps, trace widths, and colors so it can give you a cleaner results display. Additionally it can perform multiple sweeps and average the results. SWR, TDR, and all the usual parameters are shown for each marker. For the cables I tested the TDR function and it worked well also. I have a Samsung Galaxy S10 so has a USB C connector. I used the supplied short USB cable and ran the NanoVNA Web App on my phone and that worked well also. Again, more display real estate, clearer charts.As mentioned earlier there is a known issue with touch screen clearance on front case section (as of this date). You may experience random menu operation. It is due to the lack of clearance between the right edge of the display case cutout and the touch screen edge. This can happen due to variable air gap between the LCD base and the PCB and/or case flexing/warpage, or if you squeeze the case on the right side. I worked around this by slightly warping the case along the right side display edge outward a bit and then holding the unit by the edges while in use. Some put tape on the far right edge of the screen as a spacer. I also tend to use an old stylus pen from an Ancient pocketPC I still have as a museum piece. A suggested fix is small thin plastic washers on each case screw on the PCB between the 2 case halves. No doubt future case production will be adjusted. Was an easy fix once I figured out the problem.Hugen79 released a new build on Jan 18, 2020. I installed that and all works fine still. It is easy to do once you fine the right tool. I tried the most commonly suggested method using a command line tool called dfu-util.exe. It was able to see the VNA USB parameters but it claimed it was not in DFU mode (though it actually was). The latest build lets you go into DFU mode easily (a bootloader mode to update firmware). Just power off, press and hold the switch paddle in, turn the power on, and let go. The screen will be black but you will hear/see the USB device enable on your PC. You can see the device as the “STM Device in DFU Mode” in device manager under USB controllers. Some procedures suggest you run Zadig to install a Libusb driver which I did. I used the LibUSBk version. Not finding a way to make dfu-util work, I found DfuSe_Demo V3.06 from ST Microelectronics. It is a GUI based version of the tool and it worked no problem and easier as well.I have seen web posts were some folks are attempting to use the changes in hardware version 3.4 to update their pre 3.4 devices, particularly in the shielding area, some changing out resistor values and lowering noise by adding more caps inside.The NanoVNA-H4 arrived with the battery fully charged according to the on screen indicator. I plugged it in to ensure it was topped off. I used it for quite some time running on the battery and it still showed full. I believe the previous version batteries were 450-650mAH, at least for the 2.8 versions. This one at 1950mAH give a long operating time.Software mentioned:Zadig.exeLibusb driverNanoVNA-H firmware dated January 18, 2020 V4.0.4.5-12-gea578a2 NanoVNA-Saver.exe NanoVNA Web App for Android, maybe iOS also.Dfu-util.exe (did not work for me)Dfu_Se Demo V3.06.exe (worked well)In conclusion, for me this was worth hopping off the fence and is a great value covering the all the HF through 1296 bands. Well done to the project creators and contributors.